CATALOG 128 CATALOG 128.qxd 4/25/2014 7:15 AM Page 76 PCB Accessories Tools & Handles Pad Cutters, Insertion Tools Hand Insertion Tools for Pad Cutters Push-In Terminals Terminal Part Holder Type P/N No T44 A13 Shank with removable rubber handle A13-1 T68 Shank with removable rubber handle T28 P91A Wooden Handle T49 P156 Wooden Handle T46 series P133A Shank with removable rubber handle & K24 - K31 P134 K36 Wooden Handle T42-1 P149A Wooden Handle T42-1 P149 Shank with removable rubber handle A13 Shank with removable rubber handle Shank Type (A13 type) P149 Shank with removable rubber handle P149A - Wooden Handle Type Shows pad removal T107 & pad cutter P116C Shank Only Bus Strips P138C P138A Wooden Handle type Vector Pad Cutters provide an effective method for cre- ating isolated solder pads around holes in copper clad boards. Pilot pin enters hole and rotates, creating a Flat cold-drawn flat copper wire, 0.017 thick (+/-0.003) clearance area around the solder pad. Available for 0.080W with 0.042 diameter holes on 0.100 centers Hot 100% Tin dipped, fully RoHS compliant boards with.062 or .042 diameter holes. Also available Compatible with most Vectorbord hole patterns without handles for use with manual or power drills. Part Holder A B C Shank Use with Part No. Pkg Qty No. Type Vectorbord P116C Handle/Shank .055 .188 .250 .250 Pattern G, H .062 holes T107/C 100 P138A Handle/Shank .040 .086 .125 .125 Pattern P, .042: holes T107/10 10 P138C Shank Only .040 .086 .125 .125 Pattern P, .042: holes HA14 HA9 Pull Type Ejector Handle Rotation Type Ejector Handle Package Part No. Extraction/insertion handles Quantity Mounts on front edge of HA14 4 tm Plugbord with single screw HA14/C 100 or roll-pin Plastic (FE4) Dimensional information for HA9 is on Page 44 Card ejector, corner mounting Part No. Pkg Qty Supports up to 40 lbs HA9/4 extraction force 4 HA9/C White nylon, (hardware included) 100 76 www.vectorelect.com Specification subject to change without notice 800-423-5659 Tools Pad CutterCATALOG 128 CATALOG 128.qxd 4/25/2014 7:17 AM Page 78 PCB Accessories Tefzel 28 AWG Wire Insulation Properties Slit-N-Wrap Wire Property Test Method Unit Value Thermal Properities Tefzel Insulated Silver Plated Wire for o Nominal Melting Point ASTM D3159 C 255-280 use with No. 02 Bit o ( F) (491-536) Flow Rate ASTM D315 g/10 min 20 Part No. AWG Color Spool Dia. Feet/Spool Spools/Pkg o Upper Service Temperature UL746 C 135 W28-6A 28 green 1 50 2 W28-6B 28 red 1 50 2 W28-6D 28 blue 1 50 2 Mechanical Properities o o W28-6E 28 white 1 50 2 Tensile Strength, 23 C (73 F) ASTM D3159 MPa, (psi) 40, (6,500) W28-6F 28 yellow 1 50 2 Specific Gravity ASTM D792 - 1.71 W28-6H 28 black 1 50 2 o o Ultimate Elongation, 23 C (73 F) ASTM D3159 % 300 W28-6AU 28 green 1.5 150 1 o o Flexural Modulus, 23 C (73 F) ASTM D790 MPa (psi) 1,200 (170,000) W28-6BU 28 red 1.5 150 1 o o Impact Streength, 23 C (73 F) ASTM D256 J/m (ft-lb/in.) No Break W28-6DU 28 blue 1.5 150 1 Hardness, Durometer ASTM D2240 Shore D 63 W28-6EU 28 white 1.5 150 1 Compressive Strength ASTM D695 MPa, (psi) 38 (5,500) W28-6FU 28 yellow 1.5 150 1 o -5 W28-6HU 28 black 1.5 150 1 Linear Coefficient of Expansion, ASTM E831 mm/mm/ C 12.6x 10 o o o -5 0-100 C (32-212 F) in./in./ F (7.0 x 10 ) See specifications on Page 81 Electrical Properities Dielectric Strength, 0.25mm (0.010in.) ASTM D149 kV/mm (V/0.001in.) 70 (1,800) o o Dielectric Constant, 1MHz,23 C (73 F) ASTM D1531 - 2.5-2.6 o o Dissipation Factor, 1MHz,23 C (73 F) ASTM D1531 - 0.00540 3 17 . Volume Resistivity ASTM D257 ohm cm 1 x 10 (1 x 10 ) Arc Resistance ASTM D49 seconds 122 General Properities Water Absorption, 24 h ASTM D570 % 0.007 Weather and Chemical Resistance - - Excellent Limiting Oxygen Index ASTM D2863 % 30-32 Vector 28AWG Tefzel wire is rated 300V at 150 degrees C T120-1 EyeletsT15.23,T123 Slip-On Contacts 2 versions provide hole size reduction Reels of slip-on contacts. 5 apart T123 - reduces .055 dia. holes Slips onto .025 square posts to .042 28 gage PVC insulated blue wire T123 eyelets are copper with o Temperature Range: -310 to 221 F .0003 to .0005 thick tin plating o (-190 to 105 C) T15.23 - reduces .062 dia. holes to .042 Simulates copper thru hole plating Used to commit power and ground planes ID B .04 + .02 1.0 + 0.5 Contact No Contact Body Detail Board C Black Contact Shrinkable A .060 T123 Eyelet T123 Eyelet No Contact REF Tubing 1.52 End Terminal Only Part No. Qty A B C ID T15.23/M 1000 .062 .105 .093 .042 Contact Package T123/500 500 .055 .105 .093 .042 Part No. Description Quantity. T123/1000 1000 .055 .105 .093 .042 installed on wire Reel of 50 T120-1/50 installed on wire Reel of 250 T120-1/250 78 www.vectorelect.com Specification subject to change without notice 800-423-5659 Accessories