8 7 6 5 4 3 2 1 VICOR CONFIDENTIAL REV. DESCRIPTION DATE APPROVED THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT THE PERMISSION OF VICOR CORP. 3 RELEASED PER E090033 AR 01/09/09 REJH 4 REVISED PER E092035 JS 11/16/09 REJH F F 5 REDRAWN PER E100871 DCS 07/01/10 KUK 6 REVISED PER E111266 VSS 12/22/11 REJH <> 4-40 UNC-2B COLD FORM TAP .140 DP MIN. FROM FARSIDE DO NOT BREAK THRU (6) PL. E E .49 <> .650 <> 2.28 1.300 <> <> D D 2.000 .910 <> C C .11 2.220 <> .90 <> B B <> .005 .010 .190 .100 MATL TO BE REMOVED DRAWN BY DATE SWD NOTES: VICOR 1. MATERIAL: EXTRUSION SEE SHEET 2 OF 2 Robert Hickey 07/01/2010 2. REMOVE ALL BURRS AND SHARP EDGES. UNLESS OTHERWISE SPECIFIED <>3. CLEAR FINISH, RoHS COMPLAINT PER CST-0001, LATEST REVISION PER DIMENSIONS ARE : INCH / MM HTSNK LONG .9H LO FLO A)CHROMIUM FREE, OR TOLERANCES ARE: DECIMALS ANGLES A A THD B)TRIVALENT CHROMIUM IN ACCORDANCE WITH MIL-DTL-5541, TYPE II, CLASSS 1A OR 3. X.XX X.X = 0.01 0.25 1 X.XXX X.XX = 0.005 0.127 SEE CST-0003 FOR TYPES OF AVAILABLE FINISHES. SIZE CAGE CODE DWG NO REV THIRD ANGLE PROJECTION 4. < DENOTES CRITICAL CHARATERISTIC FOR LOT INSPECTION. 5. DIMENSIONS ARE INCHES ONLY. C 67131 30189 6 2:1 2 SCALE SHEET OF 1 DO NOT SCALE DRAWING 8 7 6 5 4 3 2 18 7 6 5 4 3 2 1 VICOR CONFIDENTIAL REV. DESCRIPTION DATE APPROVED THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT THE PERMISSION OF VICOR CORP. SEE SHEET 1 OF 2 F F SEE DETAIL A 3 1.5 EACH SIDE OF VERT E E 1.756 R.018 .910 (2) PL. R.035 .023 .036 .031 .215 .200 D D .110 A .040 .080 (14) PL. * .084 * .087 R.010 (2) PL. (5) PL. (2) PL. R.035 (18) PL. * .178 (2) PL. R.030 * .174 (33) PL372 (6) PL. C C .752 +.020 .007 2.220 -.000 (2) PL191 PROFILE COMMON FOR DETAIL A B B SCALE 8 : 1 30123 C L 30181 30189 30182 30188 * .087 NOTES: 1. MATERIAL: ALUMINUM 6063-T5 2. * DENOTES DIMENSION TO THEORETICAL SHARP CORNER. DRAWN BY DATE SWD VICOR 3. ALL DIMENSIONS ARE CRITICAL CHARACTERISTICS. Robert Hickey 07/01/2010 4. RoHS COMPLIANT PER CST-0001 LATEST REVISION. 5. WORKMANSHIP STANDARDS WS-0004, WS-0006, AND WS0007 APPLY TO THIS PART. UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE : INCH / MM 6. DIMENSIONS ARE INCHES ONLY. HTSNK LONG .9H LO FLO TOLERANCES ARE: DECIMALS ANGLES A A THD X.XX X.X = 0.01 0.25 1 X.XXX X.XX = 0.005 0.127 SIZE CAGE CODE DWG NO REV THIRD ANGLE PROJECTION C 67131 30189 6 1:1 2 SCALE SHEET OF 2 DO NOT SCALE DRAWING 8 7 6 5 4 3 2 1