8 7 6 5 4 3 2 1 VICOR CONFIDENTIAL REVISIONS THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT REV DESCRIPTION DATE APPROVED THE PERMISSION OF VICOR CORP. 1 RELEASED PER E053437 LEK 11/15/05 EF F F 2 DRAWN FOR DEVELOPMENT JS 08/19/09 REJH SEE NOTE 6 3 DCS 7/14/10 KUK REDRAWN PER E100902 30 DRILL THRU ( .1285 ) (6) PL120 (2) PL300 (2) PL. E E R.110 MAX (8) PL. 1.47 1.270 .130 TYP .410 SEE NOTE 5 .10 D D .650 .49 1.300 2.280 C C -A- .40 .005 .010 MATL TO BE REMOVED .190 .100 B B NOTES: 1. MATERIAL: EXTRUSION SEE SHEET 2 OF 2 2. REMOVE ALL BURRS AND SHARP EDGES. 3. CLEAR FINISH, RoHS COMPLIANT, CHROMIUM FREE PER CST-0001 LATEST REVISION. 4. DENOTES CRITICAL CHARACTERISTIC FOR LOT INSPECTION. 5. DIMENSIONS APPLIES AT SURFACE -A- (2) PL. 6. MACHINED SURFACE TO BE .010 MAX BELOW SURFACE -A- (6) PL. 7. DIMENSIONS ARE INCHES ONLY. SWD DRAWN DATE VICOR D.P.KELLY 09/05 UNLESS OTHERWISE SPECIFIED MATERIAL HS CFG X-FLOW, .4H DIMENSIONS ARE INCH MM TOLERANCES ARE: XXXXX DECIMALS ANGLES LOW FLOW, THRU HOLE A A X.XX X.X = 0.01 0.25 1 X.XXX X.XX = 0.005 0.127 SIZE CAGE CODE DWG NO REV FINISH THIRD ANGLE PROJECTION XXXXX C 67131 30722 3 SCALE 2 : 1 SHEET 1 OF 2 DO NOT SCALE DRAWING 8 7 6 5 4 3 2 18 7 6 5 4 3 2 1 VICOR CONFIDENTIAL REVISIONS THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT REV DESCRIPTION DATE APPROVED THE PERMISSION OF VICOR CORP. SEE SHEET 1 OF 2 F F E E 3 EACH 1.5 SIDE OF VERT R.035 (24) PL014 (2) PL. 1.756 SEE DETAIL A R.035 R.018 .023 .410 (2) PL. D D .036 .235 .200 .110 .040 .031 .080 R.010 * .056 * .058 (4) PL. (2) PL. (8) PL. * .138 * .133 .252 R.030 (5) PL. (6) PL. (8) PL. * .060 * .297 (2) PL. +.020 2.280 -.000 C C * .030 * .060 DETAIL A PROFILE COMMON SCALE 8 : 1 FOR TYP 30722 32173 30721 30184 B B NOTES: 1. MATL: ALUMINUM 6063-T5 2. *DENOTES DIMENSIONS TO THEORETICAL SHARP CORNER 3. ALL DIMENSIONS ARE CRITICAL CHARACTERISTICS. 4. RoHS COMPLIANT PER CST-0001 LATEST REVISION. 5. WORKMANSHIP STANDARDS WS-0004, WS-0006 AND WS-0007 APPLY TO THIS PART. 6. DIMENSIONS ARE INCHES ONLY. SWD DRAWN DATE VICOR JSARIPELLA 08/19/09 UNLESS OTHERWISE SPECIFIED MATERIAL HS CFG X-FLOW, .4H, LOW DIMENSIONS ARE INCH MM TOLERANCES ARE: SEE NOTES DECIMALS ANGLES FLOW, THRU HOLE, EXTRUSION A A X.XX X.X = 0.01 0.25 1 X.XXX X.XX = 0.005 0.127 SIZE CAGE CODE DWG NO REV FINISH THIRD ANGLE PROJECTION SEE NOTES C 67131 30722 3 SCALE 4 : 1 SHEET 2 OF 2 DO NOT SCALE DRAWING 8 7 6 5 4 3 2 1