6N139 www.vishay.com Vishay Semiconductors High Speed Optocoupler, 100 kBd, Low Input Current, Photodiode Darlington Output FEATURES High current transfer ratio, 500 % 1 8 NC V Low input current, 1.6 mA CC High common mode rejection, 500 V/s 2 7 A V B Adjustable bandwidth-access to base C 3 6 V O Material categorization: NC 4 5 GND for definitions of compliance please see www.vishay.com/doc 99912 APPLICATIONS click logo to get started DESIGN SUPPORT TOOLS Microprocessor system interface PLC, ATE input / output isolation Models Design Tools Available Available EIA RS232 line receiver TTL, CMOS voltage level translation DESCRIPTION Multiplexed data transmission High common mode transient immunity and very high current ratio together with 5300 V insulation are Digital control power supply RMS achieved by coupling and LED with an integrated high gain Ground loop and electrical noise elimination photo detector in an eight pin dual-in-line package. Separate pins for the photo diode and output stage enable AGENCY APPROVALS TTL compatible saturation voltages with high speed operation. UL 1577 Access to the base terminal allows adjustment to the gain cUL bandwidth. DIN EN 60747-5-5 (VDE 0884-5), available with option 1 The 6N139 is suited for low power logic applications involving CMOS and low power TTL applications. A 400 % current transfer ratio with only 0.5 mA of LED current is guaranteed. Caution: Due to the small geometries of this device, it should be handled with Electrostatic Discharge (ESD) precautions. Proper grounding would prevent damage further and/or degradation which may be induced by ESD. ORDERING INFORMATION DIP 6 N 13 - X 0 T 7.62 mm PART NUMBER PACKAGE OPTION TAPE Option 7 Option 9 AND REEL > 0.7 mm > 0.1 mm CTR (%) AGENCY CERTIFIED/PACKAGE 1.6 mA UL, cUL > 500 DIP-8 6N139 SMD-8, option 7 6N139-X007, 6N139-X007T SMD-8, option 9 6N139-X009, 6N139-X009T UL, cUL, VDE (option 1) > 500 DIP-8 6N139-X001 SMD-8, option 7 6N139-X017T SMD-8, option 9 6N139-X019T Note For additional information on the available options refer to option information Rev. 1.7, 24-Sep-2018 Document Number: 83605 1 For technical questions, contact: optocoupleranswers vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 6N139 www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL VALUE UNIT INPUT Reverse voltage V 5V R Forward current I 25 mA F Average input current I 20 mA f(avg) Input power dissipation P 35 mW diss OUTPUT Supply and output voltage Pin 8 to 5, pin 6 to 5 V , V -0.5 to 18 V CC O Emitter base reverse voltage Pin 5 to 7 0.5 V 50 % duty cycle - 1 ms Peak input current 40 mA pulse width Peak transient input current t 1 s, 300 pps 1 A p Output current Pin 6 I 60 mA O Output power dissipation P 100 mW diss COUPLER Storage temperature T -55 to +150 C stg Operating temperature T -55 to +100 C amb Lead soldering temperature t = 10 s T 260 C sld Note Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability ELECTRICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT INPUT Input forward voltage I = 1.6 mA V -1.4 1.7 V F F Input reverse breakdown voltage I = 10 A B 5- - V R VR Input capacitance f = 1 MHz, V = 0 C -25 - pF F IN Temperature coefficient of I = 1.6 mA - -1.8 - mV/C F forward voltage OUTPUT I = 1.6 mA, I = 8 mA, V = 4.5 V V -0.1 0.4 V F O CC OL (1) Logic low, output voltage I = 5 mA, I = 15 mA, V = 4.5 V V - 0.15 0.4 V F O CC OL I = 12 mA, I = 24 mA, V = 4.5 V V - 0.25 0.4 V F O CC OL (1) Logic high, output current I = 0 mA, V = 18 V I - 0.05 100 A F CC OH (1) Logic low supply current I = 1.6 mA, V = OPEN, V = 18 V I -0.2 1.5 mA F O CC CCL (1) Logic high supply current I = 0 mA, V = OPEN, V = 18 V I - 0.001 10 A F O CC CCH COUPLER Input output insulation leakage 45 % relative humidity, -- 1 A current T = 25 C, t = 5 s, V = 3000 V amb IO DC Coupling capacitance f = 1 MHz C - 0.6 - pF IO Notes Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements (1) Pin 7 open Rev. 1.7, 24-Sep-2018 Document Number: 83605 2 For technical questions, contact: optocoupleranswers vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000