DG2001E www.vishay.com Vishay Siliconix Powered-off Protection, 0.85 , 1.8 V to 5.5 V, SPDT Analog Switch (2:1 Multiplexer) DESCRIPTION FEATURES The DG2001E is a high performance single-pole, Low switch on-resistance (0.85 ) double-throw (SPDT) analog switch designed for 1.8 V to 1.8 V to 5.5 V single supply operation 5.5 V operation with a single power rail. Isolation in powered-off mode Fabricated with high density CMOS technology, the device Guaranteed 1.8 V logic high achieves low on resistance of 0.85 at a 5 V power supply, low power consumption, and fast switching speeds. Control logic inputs can go over V+ The DG2001E can handle both analog and digital signals Low charge injection (8 pC) and permits signals with amplitudes of up to V+ to be Break before make switching transmitted in either direction. Its control logic inputs can go Latch-up performance exceeds 300 mA per JESD 78 over V+ up to 5.5 V. The control logic input high threshold is guaranteed as low as 1.8 V over the power supply range up ESD tested to 5.5 V. It features break before make switching - 7000 V human body model (JS-001) performance. - 1000 V charge device model (JS-002) A powered-off protection circuit is built into the switch to Material categorization: for definitions of compliance prevent an abnormal current flow from COM pin to V+ during please see www.vishay.com/doc 99912 the power-down condition. Each output pin can withstand greater than 7 kV (human body model). APPLICATIONS Operation temperature is specified from -40 C to +85 C. Consumer and computing The DG2001E is available in TSOP-6 package. Portable instrumentation Medical equipment Battery operated systems FUNCTIONAL BLOCK DIAGRAM AND PIN CONFIGURATION TSOP-6 IN NO (source ) 1 6 1 H1XXX V+ COM 2 5 Pin 1 GND NC (source ) 4 3 2 Device marking: H1XXX XXX = date / lot traceability code Top view Device marking: H1 TRUTH TABLE ORDERING INFORMATION LOGIC NC NO TEMP RANGE PACKAGE PART NUMBER 0On Off -40 C to +85 C TSOP-6 DG2001EDV-T1-GE3 1Off On S18-0426-Rev. B, 23-Apr-18 Document Number: 76471 1 For technical questions, contact: analogswitchtechsupport vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000DG2001E www.vishay.com Vishay Siliconix ABSOLUTE MAXIMUM RATINGS (T = 25 C, unless otherwise noted) A PARAMETER LIMIT UNIT V+, COM, NC, NO, IN reference to GND -0.3 to 6 V Continuous current (any terminal) 50 mA Peak current (pulsed at 1 ms, 10 % duty cycle) 200 Storage temperature (D suffix) -65 to +125 C a b Power dissipation (packages) TSOP-6 570 mW ESD / HBM JS-001 7000 V ESD / CDM JS-002 1000 Latch up Per JESD78 with 1.5 x voltage clamp 300 mA Notes a. All leads welded or soldered to PC board b. Derate 7 mW/C above 25 C Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. SPECIFICATIONS (V+ = 5 V) TEST CONDITIONS LIMITS UNLESS OTHERWISE SPECIFIED -40 C to +85 C a PARAMETER SYMBOL TEMP. UNIT V+ = 5 V, 10 % b c b e MIN. TYP. MAX. V = 0.8 V or 2.4 V IN Analog Switch V , V NO NC d Analog signal range Full 0 - V+ V V COM Room - 0.85 1.6 V+ = 4.5 V On-resistance R ON V = 3 V, I , I = 10 mA COM NO NC Full - - 1.8 R V+ = 4.5 V d ON R flatness Room - 0.3 - ON Flatness V = 0 V to V+, I , I = 10 mA COM NO NC Room -5 - 5 I NO(off) I NC(off) Full -30 - 30 Switch off V+ = 5.5 V g leakage current V , V = 1 V / 4.5 V, V = 4.5 V / 1 V NO NC COM Room -5 - 5 I nA COM(off) Full -30 - 30 Room -5 - 5 Channel-on V+ = 5.5 V I g COM(on) leakage current V , V = V = 1 V / 4.5 V NO NC COM Full -30 - 30 d Power down leakage I V+ = 0 V, V = 4.5 V, V = GND Full -- 1 A COM(PD) COM IN Digital Control Input high voltage V Full 2.4 - - INH V Input low voltage V Full - - 0.8 INL Input capacitance C Full - 3 - pF IN Input current I or I V = 0 V or V+ Full -1 - 1 A INL INH IN Dynamic Characteristics Room - 15 32 Turn-on time t ON Full - - 35 V or V = 3 V, R = 300 , C = 35 pF Room - 6 26 ns NO NC L L Turn-off time t OFF Full - - 31 Break-before-make time t Room 1 4 - d d Charge injection Q C = 1 nF, V = 0 V, R = 0 Room - 8 - pC INJ L GEN GEN d Off-isolation OIRR Room - -63 - R = 50 , C = 5 pF, f = 1 MHz dB L L d Crosstalk X Room - -63 - TALK C d NO(off) Source-off capacitance Room - 16 - C NC(off) V = 0 V or V+, f = 1 MHz pF IN d Channel-on capacitance C Room - 53 - ON Power Supply Power supply current I+ V = 0 V or V+ Full - 0.0003 1 A IN S18-0426-Rev. B, 23-Apr-18 Document Number: 76471 2 For technical questions, contact: analogswitchtechsupport vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000