K3010P, K3010PG Series www.vishay.com Vishay Semiconductors Optocoupler, Phototriac Output, Non-Zero Crossing, 250 V DRM FEATURES SMD Isolation materials according to UL 94 V-0 MT2 A 1 6 Special construction: therefore, extra low coupling capacity of typical 0.2 pF, high 2 5 NC C common mode rejection I of 5 mA, 10 mA, and 15 mA FT 3 4 NC MT1 DIP Rated impulse voltage (transient overvoltage) V = 8 kV IOTM peak Isolation test voltage, 5300 V , t = 1 s RMS Material categorization: For definitions of compliance please see www.vishay.com/doc 99912 i179041-2 APPLICATIONS Circuits for safe protective separation against electrical DESCRIPTION shock according to safety class II (reinforced isolation): The K3010P, K3010PG series consists of a photo-transistor for appl. class I to IV at mains voltage 300 V optically coupled to a gallium arsenide infrared-emitting for appl. class I to IV at mains voltage 600 V diode in a 6-pin plastic dual inline package according to DIN EN60747-5-5 (VDE0884), suitable for: AGENCY APPROVALS - Monitors UL1577, file no. E52744 system code H, double protection - Air conditioners BSI: BS EN60065:2002 and IEC 60065:2001, certificate - Line switches number 7955. An BS EN60950-1:2006 certificate number - Solid state relay 7956 - Microwave DIN EN 60747-5-5 CQC: GB8898-2001 ORDERING INFORMATION DIP-6 G leadform K 3 0 1 0P X0 T 10.16 mm 7.62 mm PART NUMBER TRIGGER PACKAGE OPTION TAPE AND CURRENT REEL Option 7 BIN > 0.7 mm AGENCY CERTIFIED/PACKAGE TRIGGER CURRENT, I FT VDE, cUL, BSI 5 mA 10 mA 15 mA DIP-6 K3012P K3011P K3010P DIP-6, 400 mil K3012PG K3011PG K3010PG SMD-6, option 7 K3012P-X007T - K3010P-X007T Note G = leadform 10.16 mm G is not marked on the body. Rev. 2.2, 01-Jun-12 Document Number: 83504 1 For technical questions, contact: optocoupleranswers vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 K3010P, K3010PG Series www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL VALUE UNIT INPUT Reverse voltage V 5V R Forward current I 80 mA F Forward surge current t 10 s I 3A p FSM Power dissipation P 100 mW diss Junction temperature T 100 C j OUTPUT Off state output terminal voltage V 250 V DRM On state RMS current I 100 mA TRM Peak surge current, non-repetitive t 10 ms I 1.5 A p TMS Power dissipation P 300 mW diss Junction temperature T 100 C j COUPLER Isolation test voltage (RMS) t = 1 s V 5300 V ISO RMS Total power dissipation P 350 mW tot Storage temperature range T - 55 to + 150 C stg Ambient temperature range T - 55 to + 100 C amb (1) Soldering temperature 2 mm from case, t 10 s T 260 C sld Notes Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. (1) Refer to wave profile for soldering conditions for through hole devices (DIP) Assembly Instructions (www.vishay.com/doc 80054) ELECTRICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. UNIT INPUT Forward voltage I = 50 mA V 1.25 1.6 V F F Junction capacitance V = 0, f = 1 MHz C 50 pF R j OUTPUT Forward peak off-state voltage (1) I = 100 nA V 250 V RDM DRM (repetitive) Peak on-state voltage I = 100 mA V 1.5 3 V TM TM dV/d 10 V/s tcr Critical rate of rise of off-state voltage I = 0, I = 30 mA FT FT dV/d 0.1 0.2 V/s tcrq (2) COUPLER K3010P I 815 mA FT K3010PG I 815 mA FT K3011P I 510 mA FT Collector emitter trigger current V = 3 V, R = 150 S L K3011PG I 510 mA FT K3012P I 25 mA FT K3012PG I 25 mA FT Holding current I = 10 mA, V 3 V I 100 A F S H Notes Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements. (1) Test voltage must be applied within dV/dt ratings. (2) I is defined as a minimum trigger current. FT Rev. 2.2, 01-Jun-12 Document Number: 83504 2 For technical questions, contact: optocoupleranswers vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000