LH1501BABTR Vishay

333 3 LH1501BAB, LH1501BABTR, LH1501BT www.vishay.com Vishay Semiconductors 1 Form B Solid State Relay FEATURES SMD S S Isolation test voltage 3750 V RMS Typical R 20 ON S DC S 65 4 Load voltage 350 V Clean bounce free switching DIP Low power consumption SMD lead available on tape and reel 12 3 Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 i179041-2 APPLICATIONS LINKS TO ADDITIONAL RESOURCES General telecom switching Security equipment Design Tools Models 3D Models Instrumentation DESCRIPTION Industrial controls The LH1501 relays are SPST normally closed switches AGENCY APPROVALS (1 form B) that can replace electromechanical relays in many UL applications. The relays are constructed as a multi-chip hybrid device. Actuation control is via an infrared LED. The VDE output switch is a combination of a photodiode array with MOSFET switches and control circuity. The relays can be configured for AC/DC or DC only operation. ORDERING INFORMATION SMD DIP L H 1501 B T R PART NUMBER ELECTR. PACKAGE TAPE AND > 0.1 mm 7.62 mm VARIATION CONFIG. REEL PACKAGE UL, CSA SMD-6, tubes LH1501BAB SMD-6, tape and reel LH1501BABTR DIP-6, tubes LH1501BT Rev. 1.8, 13-Oct-2020 Document Number: 83805 1 For technical questions, contact: optocoupleranswers vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 DDD D LH1501BAB, LH1501BABTR, LH1501BT www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL VALUE UNIT INPUT LED continuous forward current I 50 mA F LED reverse voltage I 10 A V 5V R R OUTPUT DC or peak AC load voltage I 50 A V 350 V L L Continuous DC load current - bidirectional I 150 mA L Continuous DC load current - unidirectional I 200 mA L Peak load current (single shot) t = 100 ms I 350 mA P SSR Ambient temperature range T -40 to +85 C amb Storage temperature range T -40 to +125 C stg (1) Pin soldering temperature t = 10 s max. T 260 C sld Input to output isolation voltage t = 1 s, I = 10 A max. V 3750 V ISO ISO RMS Output power dissipation (continuous) P 550 mW diss Notes Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability (1) Refer to reflow profile for soldering conditions for surface mounted devices (SMD). Refer to wave profile for soldering conditions for through hole devices (DIP) ELECTRICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT INPUT LED forward current, switch turn-on I = 150 mA, t = 10 ms I 0.2 0.9 mA L Fon LED forward current, switch turn-off V = 300 V I 12 mA L Foff LED forward voltage I = 10 mA V 1.15 1.26 1.45 V F F OUTPUT On-resistance, AC/DC: pin 4, 6 (+) to 5 (-) I = 0 mA, I = 50 mA R 20 25 F L ON On-resistance, DC: pin 4, 6 (+) to 5 (-) I = 0 mA, I = 100 mA R 56.25 F L ON Off-resistance I = 5 mA, V = 100 V R 0.1 1.4 G F L OFF Off-state leakage current I = 5 mA, V = 350 V I 0.08 1 A F L O Output capacitance I = 5 mA, V = 50 V C 35 pF F L O TRANSFER Capacitance (input to output) V = 1 V C 3pF ISO IO Note Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluations. Typical values are for information only and are not part of the testing requirements. SWITCHING CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Turn-on time I = 5 mA, I = 50 mA t 23 ms F L on Turn-off time I = 5 mA, I = 50 mA t 13 ms F L off Rev. 1.8, 13-Oct-2020 Document Number: 83805 2 For technical questions, contact: optocoupleranswers vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000