RCWPM (Military M/D55342) www.vishay.com Vishay Dale Thick Film Chip Resistors, Military/Established Reliability MIL-PRF-55342 Qualified, Type RM FEATURES Fully conforms to the requirements of MIL-PRF-55342 Established reliability - verified failure rate M, P, R, U, S, V, and T levels Construction is sulfur impervious against a high sulfur environment (ASTM B 809-95 test method) 100 % group A screening per MIL-PRF-55342 Termination style B - tin/lead wraparound over nickel barrier MATERIAL SPECIFICATIONS Operating temperature range is -55 C to +150 C Resistive element Ruthenium oxide For MIL-PRF-32159 zero ohm jumpers, see Vishay Dales Encapsulation Epoxy RCWPM Jumper (Military M32159) datasheet Substrate 96 % alumina (www.vishay.com/doc 31028) Termination Solder-coated nickel barrier Material categorization: for definitions of compliance Solder finish Tin/lead solder alloy please see www.vishay.com/doc 99912 STANDARD ELECTRICAL SPECIFICATIONS POWER MAX. MIL RESISTANCE TEMPERATURE VISHAY DALE MIL-PRF-55342 CASE RATING WORKING TOLERANCE (2) SPEC. TERM. RANGE COEFFICIENT (1) MODEL STYLE SIZE P VOLTAGE % 70 C SHEET ppm/C W V 1 to 9.1 2, 5, 10 200, 300 RCWPM-0502, RM0502 01 B 0502 0.05 40 10 to 22M 1, 2, 5, 10 100, 200, 300 RCWPM-0502-98 10 to 10M 0.5 100, 200, 300 1 to 9.1 2, 5, 10 200, 300 RCWPM-550, RM0505 02 B 0505 0.125 40 10 to 22M 1, 2, 5, 10 100, 200, 300 RCWPM-550-98 10 to 10M 0.5 100, 200, 300 1 to 5.1 2, 5, 10 200, 300 RCWPM-5100, RM1005 03 B 1005 0.20 75 5.6 to 22M 1, 2, 5, 10 100, 200, 300 RCWPM-5100-98 5.62 to 10M 0.5 100, 200, 300 1 to 5.1 2, 5, 10 200, 300 RCWPM-5150, RM1505 04 B 1505 0.15 125 5.6 to 22M 1, 2, 5, 10 100, 200, 300 RCWPM-5150-98 5.62 to 10M 0.5 100, 200, 300 1 to 5.1 2, 5, 10 200, 300 RCWPM-7225, RM2208 05 B 2208 0.225 175 5.6 to 22M 1, 2, 5, 10 100, 200, 300 RCWPM-7225-98 5.62 to 10M 0.5 100, 200, 300 1 to 5.1 2, 5, 10 200, 300 RCWPM-575, (3) RM0705 06 B 0705 0.15 50 5.6 to 22M 1, 2, 5, 10 100, 200, 300 RCWPM-575-98 5.62 to 10M 0.5 100, 200, 300 1 to 5.1 2, 5, 10 200, 300 RCWPM-1206, RM1206 07 B 1206 0.25 100 5.6 to 22M 1, 2, 5, 10 100, 200, 300 RCWPM-1206-98 5.62 to 10M 0.5 100, 200, 300 1 to 5.1 2, 5, 10 200, 300 RCWPM-2010, RM2010 08 B 2010 0.80 150 5.6 to 22M 1, 2, 5, 10 100, 200, 300 RCWPM-2010-98 5.62 to 10M 0.5 100, 200, 300 1 to 5.1 2, 5, 10 200, 300 RCWPM-2512, RM2512 09 B 2512 1.0 200 5.6 to 22M 1, 2, 5, 10 100, 200, 300 RCWPM-2512-98 5.62 to 10M 0.5 100, 200, 300 1 to 5.1 2, 5, 10 200, 300 RCWPM-1100, RM1010 10 B 1010 0.50 75 5.6 to 22M 1, 2, 5, 10 100, 200, 300 RCWPM-1100-98 5.62 to 10M 0.5 100, 200, 300 1 to 9.1 2, 5, 10 200, 300 RCWPM-0402, RM0402 11 B 0402 0.05 30 10 to 22M 1, 2, 5, 10 100, 200, 300 RCWPM-0402-98 10 to 10M 0.5 100, 200, 300 Revision: 15-Oct-15 Document Number: 31010 1 For technical questions, contact: ff2aresistors vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 RCWPM (Military M/D55342) www.vishay.com Vishay Dale STANDARD ELECTRICAL SPECIFICATIONS POWER MAX. MIL RESISTANCE TEMPERATURE VISHAY DALE MIL-PRF-55342 CASE RATING WORKING TOLERANCE (2) SPEC. TERM. RANGE COEFFICIENT (1) MODEL STYLE SIZE P VOLTAGE % 70 C SHEET ppm/C W V 1 to 5.1 2, 5, 10 200, 300 RCWPM-0603, RM0603 12 B 0603 0.10 50 5.6 to 22M 1, 2, 5, 10 100, 200, 300 RCWPM-0603-98 5.62 to 10M 0.5 100, 200, 300 1 to 9.1 2, 5, 10 200, 300 RCWPM-0302, RM0302 13 B 0302 0.04 15 10 to 22M 1, 2, 5, 10 100, 200, 300 RCWPM-0302-98 10 to 10M 0.5 100, 200, 300 Notes DSCC has created a series of drawings to support the need for 0201-sized product. Vishay Dale is listed as a resource on this drawing as follows: POWER RATING MAX. WORKING DSCC DRAWING VISHAY DALE RES. RANGE RES. TOL. TEMP. COEF. (1) TERM. P VOLTAGE 70 C NUMBER MODEL % ppm/C W V 10 to 46.4 200 07009 RCWP-0201 B 0.05 1, 5 30 47 to 1M 100 This drawing can be viewed at: www.landandmaritime.dla.mil/Programs/MilSpec/ListDwgs.aspx DocTYPE=DSCCdwg. (1) Continuous working voltage shall be P x R or maximum working voltage, whichever is less. (2) Characteristics: K = 100 ppm/C L = 200 ppm/C M = 300 ppm/C. (3) MIL case size 0705 and EIA case size 0805 are dimensionally the same. GLOBAL PART NUMBER INFORMATION New Global Part Numbering: M55342M02B10E0RWB (preferred part number format) M 55342 M 0 2 B1 0 E 0 R W B MIL SPEC. TERMINATION VALUE AND FAILURE (1) CHARACTERISTICS PACKAGING SPECIAL STYLE SHEET STYLE TOLERANCE RATE D55342 K = 100 ppm (see Standard B = Pre-tinned (see Tolerance C = Non-ER TP = Tin/lead, Blank = applies to L = 200 ppm Electrical nickel barrier, and Multipliers M = 1.0 %/1000 h T/R (full) Standard Style 07 M = 300 ppm Specifications wraparound table) P = 0.1 %/1000 h TN = Tin/lead, (Dash number) (RM1206) table) R = 0.01 %/1000 h T/R (full), w/ESD (Up to 1 digits) (2) only. U = 0.01 %/1000 h UL = Tin/lead, T/R D = 0.5 % (3) S = 0.001 %/1000 h single lot date code tolerance (2) M55342 V = 0.001 %/1000 h S3 = Tin/lead, S = applies to T = Space level T/R (1000 pieces) Space level all other SV = Tin/lead, T/R w/option 1 part (4) styles. (1000 pieces), w/ESD marking (-97) WB = Tin/lead, T = waffle tray Space level (-98) WA = Tin/lead, 2 = waffle tray, Option 1 w/ESD part marking (4) WL = Tin/lead, (-20) waffle tray, 3 = single lot date code Options 2 and 3 S2 = Tin/lead, part marking (4) T/R (500 pieces) (-30) SU = Tin/lead, T/R (500 pieces), w/ESD S6 = Tin/lead, T/R (300 pieces) ST = Tin/lead, T/R (300 pieces), w/ESD Historical Part Numbering: M55342M02B10E0R (will continue to be accepted) M55342 M 02 B 10E0 R WB MIL TERMINATION VALUE AND FAILURE PACKAGING CHARACTERISTICS SPEC. SHEET STYLE STYLE TOLERANCE RATE CODE Notes For additional information on packaging, refer to the Surface Mount Resistor Packaging document (www.vishay.com/doc 31543). (1) Products with space level failure rates are only offered in packaging codes with ESD overpack and labeling. For all other failure rates, the ESD pack codes are an optional type of packaging. (2) Failure rates U and V require group A and B inspection ran on each production lot. (3) Add a D after the packaging code at the end of the global part number to specify Vishay Dale Thick Film product with a tolerance of 0.5 %. (4) MIL spec option 1, 2, and 3 part marking is not offered for the slash sheet 01, 02, 11, and 13 sizes. Revision: 15-Oct-15 Document Number: 31010 2 For technical questions, contact: ff2aresistors vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000