MAL804323321E3 Vishay

Accessories www.vishay.com Vishay BCcomponents Aluminum Electrolytic Capacitors - Accessories (Vishay BCcomponents) RESISTORS FOR TERMINAL MOUNTING Resistors are used to balance the voltage over a series connection of screw terminal capacitors or to ensure discharge to a safe voltage after power down. Vishay provides the CMS series of resistors, which are suited for direct mounting on the terminals of screw terminal capacitors. DIMENSIONS in inches millimeters 45 10 M 3/4 TYP. A B C CORE DIMENSIONS in inch mm TERMINAL DESIGNATION DIAMETER MODEL CM CA A B C M HOLE DIAMETER HOLE DIAMETER TYPICAL 0.031 0.79 0.062 1.59 0.0118 0.3 TYPICAL TYPICAL 0.562 0.312 1.250 0.875 0.196 50 mm CMS16 0.265 14.27 7.92 31.75 22.23 4.98 0.562 0.312 1.75 1.13 0.196 0.265 65 mm CMS20 14.27 7.92 44.45 28.7 4.98 6.73 76 mm 0.562 0.312 1.75 1.254 0.196 0.265 CMS22 14.27 7.92 44.45 31.85 4.98 6.73 90 mm MOUNTING ACCESSORIES CLAMPS FOR ST TYPES To facilitate vertical mounting, a series of rigid clamps is available. These are made of zinc plated steel, chromium (III) passivated, or stainless steel ( D = 76 mm). The clamps have either two or three mounting lugs, may be easily slipped over the capacitor and then clamped with a nut and bolt. Five types of clamps are available, one for each case diameter. They are delivered without nuts or bolts. To avoid damaging the insulation sleeve, do not overtighten the clamp screw. Revision: 01-Dec-17 Document Number: 28348 1 For technical questions, contact: aluminumcaps2 vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 9100010.5 D 120 Accessories www.vishay.com Vishay BCcomponents DIMENSIONS in millimeters AND AVAILABLE FORMS 12.05 12 0.5 11.05 7 6 1 6 1 1 60 12.5 max. 63 4 min. 10.5 51.5 0.2 35 4.4 min 60 12 0 4.5 0.5 - 0.5 35 50 49 23.5 10 67.5 4.5 0.1 66.5 80 max. Fig. 1 - Dimensional outline of clamp for case D = 35 mm Fig. 2 - Dimensional outline of clamp for case D = 50 mm 12.5 19 28.5 11.5 7 1 1 6 12.5 max. 15 4.5 60 10.5 4.5 4.4 min. 7 12.5 60 89 65 99 64 88.5 87.5 101 max. Fig. 3 - Dimensional outline of clamp for case D = 65 mm Fig. 4 - Dimensional outline of clamp for case D = 76 mm 11 5.5 24 0.5 30 1 4.5 4.5 0.5 90 101.6 0.5 111.1 1 Fig. 5 - Dimensional outline of clamp for case D = 90 mm Revision: 01-Dec-17 Document Number: 28348 2 For technical questions, contact: aluminumcaps2 vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 120(3 x) 5 0.3 10.5 14 7 1 4.2 0.1 12