OLED-096O064A-LPP3N00000 www.vishay.com Vishay 96 x 64 Graphic OLED FEATURES Type: graphic Display format: 96 x 64 dots Built-in controller: SSD1305Z Duty cycle: 1/64 +3 V power supply 2 Interface: 6800, 8080, SPI, I C With polarizer Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 MECHANICAL DATA ABSOLUTE MAXIMUM RATINGS ITEM STANDARD VALUE UNIT STANDARD VALUE ITEM SYMBOL UNIT Module dimension 24.9 x 22.95 x 1.65 MIN. MAX. Viewing area 21.953 x 15.424 Supply voltage V -0.3 4 DD (1)(2) for logic Active area 19.946 x 13.418 V mm Supply voltage Dot size 0.186 x 0.188 V 015 (1)(2) CC for display Dot pitch 0.208 x 0.210 Operating T -40 +80 OP Mounting hole n/a temperature C Storage T -40 +80 STG temperature Notes (1) All the above voltages are on the basis of V = 0 V SS (2) When this module is used beyond the above absolute maximum ratings, permanent breakage of the module may occur. Also, for normal operations, it is desirable to use this module under the conditions according to Electrical Characteristics. If this module is used beyond these conditions, malfunctioning of the module can occur and the reliability of the module may deteriorate ELECTRICAL CHARACTERISTICS STANDARD VALUE ITEM SYMBOL CONDITION UNIT MIN. TYP. MAX. Supply voltage for logic V - 2.8 3.0 3.3 DD Supply voltage for display V - 111213 CC Input high voltage V - 0.8 V -V IH DD DDI/O V Input low voltage V - 0 - 0.2 V IL DD Output high voltage V - 0.9 V -V OH DD DDI/O Output low voltage V - 0 - 0.1 V OL DD 50 % check board operating current I V = 12 V 5.8 6.0 7.5 mA CC CC OPTIONS EMITTING COLOR YELLOW GREEN RED BLUE WHITE Yes ---- Revision: 11-Aug-17 Document Number: 37835 1 For technical questions, contact: displays vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 OLED-096O064A-LPP3N00000 www.vishay.com Vishay INTERFACE PIN FUNCTION PIN NO. SYMBOL I/O FUNCTION Reserved pin (supporting pin) 1 NC (GND) - The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground Power supply for OLED panel 2V P CC This is the most positive voltage supply pin of the chip. It must be supplied externally Ground of logic circuit 3V P SS This is a ground pin. It also acts as a reference for the logic pins. It must be connected to external ground Power supply for logic circuit 4V P DD This is a voltage supply pin. It must be connected to external source Power supply for interface logic level. It should be match with MCU interface voltage level. V must DDI/O 5V P DDI/O always be equal or lower than V DD Communicating protocol select. These pins are MCU interface selection input. See the following table: 6BS1 2 68XX-parallel 80XX-parallel Serial I C I BS1 0 1 0 1 7BS2 BS2 1 1 0 0 Chip select 8CS I This pin is the chip select input. The chip is enabled for MCU communication only when CS is pulled low Power reset for controller and driver 9RES I This pin is reset signal input. When the pin is low, initialization of the chip is executed Data / command control This pin is data / command control pin. When the pin is pulled high, the input at D7 to D0 is treated as display data.When the pin is pulled low, the input at D7 to D0 will be transferred to the command register. For detail 10 D / C I relationship to MCU interface signals, please refer to the timing characteristics diagrams. When the pin is pulled high and serial interface mode is selected, the data at SDIN is treated as data. When 2 it is pulled low, the data at SDIN will be transferred to the command register. In I C mode, this pin acts as SA0 for slave address selection Read / write selector write This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as 11 R / W I read / write (R / W ) selection input. Pull this pin to high for read mode and pull it to low for write mode. When 80XX interface mode is selected, this pin will be the write (WR ) input. Data write operation is initiated when this pin is pulled low and the CS is pulled low Read / write enable or read This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as 12 E / RD I the enable (E) signal. Read / write operation is initiated when this pin is pulled high and the CS is pulled low. When connecting to an 80XX-microprocessor, this pin receives the read (RD ) signal. Data read operation is initiated when this pin is pulled low and CS is pulled low 13 14 15 Host data in put / output bus These pins are 8-bit bi-directional data bus to be connected to the microprocessors data bus. When serial 16 2 D0 to D7 I/O mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. When I C 17 mode is selected, D2 and D1 should be tired together and serve as SDA and SDA in application and D0 out in 18 is the serial clock input SCL 19 20 Current reference for brightness adjustment 21 I I This pin is segment current reference pin. A resistor should be connected between this pin and V . Set the REF SS current lower than 10 A Voltage output high level for COM signal 22 V O This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected COMH between this pin and V SS Power supply for OLED panel 23 V P CC This is the most positive voltage supply pin of the chip. It must be supplied externally 24 V P Ground of analog circuit. This is an analog ground pin. It should be connected to V externally LSS SS Reserved pin (supporting pin) 25 NC (GND) - The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground Revision: 11-Aug-17 Document Number: 37835 2 For technical questions, contact: displays vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000