PTCCL - 265 V Series www.vishay.com Vishay BCcomponents 265 V PTC Thermistors for Overload Protection FEATURES Wide range of trip and non-trip currents: From 11 mA up to 800 mA Small ratio between trip and non-trip currents (I /I = 1.5 at 25 C) t nt High maximum inrush current (up to 5.5 A) Leaded parts withstand mechanical stresses and vibration UL file E148885 according to XGPU standard UL1434 Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 APPLICATIONS Overload (current, voltage, temperature) protection in: Industrial electronics Consumer electronics Electronic data processing DESCRIPTION These directly heated ceramic-based thermistors have a QUICK REFERENCE DATA positive temperature coefficient and are primarily intended PARAMETER VALUE UNIT for overload protection. They consist of a ceramic pellet Maximum voltage (RMS or DC) 265 V soldered between two tinned CCS wires and coated with a Maximum holding current (I ) 0.011 to 0.8 A nt UL 94 V-0 high temperature hard silicone lacquer. Resistance at 25 C (R ) 2.1 to 3000 25 Tolerance on R value 20 % MOUNTING 25 Maximum overload current I 0.8 to 5.5 A ol PTC thermistors can be mounted by wave, reflow, or Switching temperature 135 to 145 C hand-soldering. Current levels have been determined according IEC 60738 conditions. Different ways of Operating temperature range 0 to 70 C at max. voltage mounting or connecting the thermistors can influence their Storage temperature -40 to +175 C thermal and electrical behavior. Standard operation is in still air, any potting or encapsulation of PTC thermistors is not QUALITY recommended and will change its operating characteristics. Typical Soldering UL approved PTCs are guaranteed to withstand severe test 235 C duration: 5 s (Lead (Pb)-bearing) programs and have factory audited follow-up programs. 245 C, duration: 5 s (Lead (Pb)-free) Major UL qualification tests are long-life (6000 cycles) electrical cycle tests at trip-current, long-life stability Resistance to Soldering Heat storage tests (3000 h at 250 C), damp heat and water 260 C, duration: 10 s max. immersion tests and over-voltage tests up to 200 % of rated voltage. MARKING UL approved PTCs are guaranteed to withstand severe test Only the gray lacquered thermistors with a diameter of programs 8.5 mm to 20.5 mm are marked with BC, R value (example 25 1R9) on one side and I , V on the other side. Long-life cycle tests (over 5000 trip cycles) nt max. Long-life storage tests (3000 h at 250 C) Electrical cycle tests at low ambient temperatures (-40 C or 0 C) Damp-heat and water immersion tests Overvoltage tests at up to 200 % of rated voltage Revision: 21-Sep-15 Document Number: 29087 1 For technical questions, contact: nlr vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 PTCCL - 265 V Series www.vishay.com Vishay BCcomponents ELECTRICAL DATA AND ORDERING INFORMATION ORDERING PART NUMBERS I MAX. I MIN. R I MAX. I MAX. at DISSIP. D nt t 25 ol res at 25 C at 25 C 20 % at 25 C V and FACTOR MAX. max. BULK TAPE ON REEL (1) (1) (2) (1) (1) (mA) (mA) () (mA) 25 C (mA) (mW/K) (mm) 11 17 3000 80 6.5 7.3 5 PTCCL05H110HBE PTCCL05H110HTE 15 23 1900 110 6.5 7.3 5 PTCCL05H150HBE PTCCL05H150HTE 19 29 1200 140 6.5 7.3 5 PTCCL05H190HBE PTCCL05H190HTE 28 42 500 200 6.8 7.3 5 PTCCL05H280HBE PTCCL05H280HTE 39 59 260 300 6.8 7.3 5 PTCCL05H390HBE PTCCL05H390HTE 63 95 120 450 7 7.3 5 PTCCL05H630HBE PTCCL05H630HTE 76 115 85 550 7 7.3 5 PTCCL05H760HBE PTCCL05H760HTE 95 143 56 600 7 7.3 5 PTCCL05H950HBE PTCCL05H950HTE 110 165 48 650 7.5 8.3 7 PTCCL07H111HBE PTCCL07H111HTE 140 210 29 800 8 8.3 7 PTCCL07H141HBE PTCCL07H141HTE 170 255 22 900 9 9 8.5 PTCCL09H171HBE PTCCL09H171HTE 190 285 18 1000 9.5 9 8.5 PTCCL09H191HBE PTCCL09H191HTE 210 315 17 1300 10 10.5 10.5 PTCCL11H211HBE PTCCL11H211HTE 250 375 12 1500 11 10.5 10.5 PTCCL11H251HBE PTCCL11H251HTE 280 420 11 1800 12 11.7 12.5 PTCCL13H281HBE PTCCL13H281HTE 320 480 8.4 2200 13 11.7 12.5 PTCCL13H321HBE PTCCL13H321HTE 400 600 6.6 3000 15 15.5 16.5 PTCCL17H401HBE - 490 735 4.4 3500 16 15.5 16.5 PTCCL17H491HBE - 590 855 4 4500 19.5 19.8 20.5 PTCCL21H591HBE - 700 1050 2.8 5500 21 19.8 20.5 PTCCL21H701HBE - (3) 800 1200 2.1 5500 22.5 19.8 20.5 PTCCL21H801HBE - Notes (1) The indicated current levels are guaranteed according IEC 60738 mounting conditions. For different mounting conditions the indicated current levels can change and should be evaluated in the application. (2) I is the maximum overload current that may flow through the PTC when it passes from the low ohmic to the high ohmic state. ol max. UL approval: I x 0.85 ol max. (3) Not UL approved CURRENT DEVIATION AS A FUNCTION OF THE AMBIENT TEMPERATURE 250 % 200 I t 150 I nt I 100 ol max. 50 0 -50 -25 0 25 50 75 100 T (C) amb Revision: 21-Sep-15 Document Number: 29087 2 For technical questions, contact: nlr vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000