TSOP2256 Vishay

333 3 TSOP22.., TSOP24.., TSOP48.., TSOP44.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Improved immunity against HF and RF noise Low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Supply voltage: 2.5 V to 5.5 V Improved immunity against optical noise Insensitive to supply voltage ripple and rnoise 1 22 Material categorization: 33 16672 for definitions of compliance please see www.vishay.com/doc 99912 LINKS TO ADDITIONAL RESOURCES MECHANICAL DATA Product Page 3D Models Calculators Marking Packages Pinning for TSOP44.., TSOP48..: 1 = OUT, 2 = GND, 3 = V S Holders Bends and Cuts Pinning for TSOP22.., TSOP24..: 1 = OUT, 2 = V , 3 = GND S DESCRIPTION The TSOP22.., TSOP48.., TSOP24.. and TSOP44.. series ORDERING CODE are miniaturized IR receiver modules for infrared remote TSOP2..., TSOP4... - 2160 pieces in tubes control systems. A PIN diode and a preamplifier are assembled on lead frame, the epoxy package contains an IR filter. BLOCK DIAGRAM The demodulated output signal can be directly connected to V S a microprocessor for decoding. The TSOP24.., TSOP44.. series devices are optimized to 30 k suppress almost all spurious pulses from Wi-Fi and CFL OUT sources. They may suppress some data signals if Band Demo- continuously transmitted. Input AGC pass dulator The TSOP22.., TSOP48.. series devices are provided primarily for compatibility with old AGC2 designs. New GND designs should prefer the TSOP24.., TSOP44.. series PIN Control circuit containing the newer AGC4. 16833-22 These components have not been qualified according to automotive specifications. APPLICATION CIRCUIT 17170-11 R 1 Transmitter IR receiver with V + V S S TSALxxxx C 1 C OUT V O GND GND R and C recommended to reduce supply ripple for V < 2.8 V 1 1 S Rev. 2.2, 14-Dec-2021 Document Number: 82459 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 DDD D Circuit TSOP22.., TSOP24.., TSOP48.., TSOP44.. www.vishay.com Vishay Semiconductors PARTS TABLE LEGACY, FOR RECOMMENDED FOR AGC LONG BURST REMOTE CONTROLS (AGC2) LONG BURST CODES (AGC4) 30 kHz TSOP4830 TSOP2230 TSOP4430 TSOP2430 33 kHz TSOP4833 TSOP2233 TSOP4433 TSOP2433 (1)(2)(3) (1)(2)(3) 36 kHz TSOP4836 TSOP2236 TSOP4436 TSOP2436 Carrier frequency (4)(5)(6) (4)(5)(6) 38 kHz TSOP4838 TSOP2238 TSOP4438 TSOP2438 40 kHz TSOP4840 TSOP2240 TSOP4440 TSOP2440 (6)(7) (6)(7) 56 kHz TSOP4856 TSOP2256 TSOP4456 TSOP2456 Package Mold Pinning 1 = OUT, 2 = GND, 3 = V 1 = OUT, 2 = V , 3 = GND 1 = OUT, 2 = GND, 3 = V 1 = OUT, 2 = V , 3 = GND S S S S Dimensions (mm) 6.0 W x 6.95 H x 5.6 D Mounting Leaded Application Remote control (1) (2) (3) (4) (5) (6) (7) Best choice for RC-5 RC-6 Panasonic NEC Sharp r-step Thomson RCA Narrow optical filter: www.vishay.com/doc 81590 Special options Wide optical filter: www.vishay.com/doc 82726 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +6 V S Supply current I 5mA S Output voltage V -0.3 to 5.5 V O Voltage at output to supply V - V -0.3 to (V + 0.3) V S O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Soldering temperature t 10 s, 1 mm from case T 260 C sd Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating onl y and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specificatio n is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT E = 0, V = 5 V I 0.55 0.7 0.9 mA v S SD Supply current E = 40 klx, sunlight I -0.8 - mA v SH Supply voltage V 2.5 - 5.5 V S E = 0, test signal see Fig. 1, v Transmission distance IR diode TSAL6200, d- 24 - m I = 50 mA F 2 I = 0.5 mA, E = 0.7 mW/m , OSL e Output voltage low V - - 100 mV OSL test signal see Fig. 1 Pulse width tolerance: 2 Minimum irradiance t - 5/f < t < t + 6/f , E - 0.12 0.25 mW/m pi o po pi o e min. test signal see Fig. 1 t - 5/f < t < t + 6/f , pi o po pi o 2 Maximum irradiance E 50 - - W/m e max. test signal see Fig. 1 Angle of half transmission Directivity - 45 - deg 1/2 distance Rev. 2.2, 14-Dec-2021 Document Number: 82459 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000