TSOP331.., TSOP333.., TSOP335.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Very low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Supply voltage: 2.5 V to 5.5 V Improved immunity against ambient light Insensitive to supply voltage ripple and noise Compatible with wave or reflow soldering (see P version of Minimold option datasheets) Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 DESCRIPTION MECHNICAL DATA The TSOP33... series are miniaturized IR receiver modules Pinning for TSOP33...: for infrared remote control systems. A PIN diode and a preamplifier are assembled on lead frame, the epoxy 1 = OUT, 2 = GND, 3 = V S package contains an IR filter. The demodulated output signal can be directly connected to a microprocessor for decoding. The TSOP333.. series devices are optimized to suppress almost all spurious pulses from energy saving lamps like CFLs. AGC3 may also suppress some data signals if continuously transmitted. The TSOP331.. series are provided primarily for compatibility with old AGC1 designs. New designs should prefer the TSOP333.. series containing the newer AGC3. The TSOP335.. series contain a very robust AGC5. This series should only be used for critically noisy environments. These components have not been qualified according to automotive specifications. PARTS TABLE LEGACY, FOR SHORT BURSTS FOR SHORT BURSTS, NOISY FOR SHORT BURSTS, VERY AGC (AGC1) ENVIRONMENTS (AGC3) NOISY ENVIRONMENTS (AGC5) 30 kHz TSOP33130 TSOP33330 TSOP33530 33 kHz TSOP33133 TSOP33333 TSOP33533 (1)(2) 36 kHz TSOP33136 TSOP33336 TSOP33536 Carrier frequency (3)(4)(5)(6) 38 kHz TSOP33138 TSOP33338 TSOP33538 40 kHz TSOP33140 TSOP33340 TSOP33540 56 kHz TSOP33156 TSOP33356 TSOP33556 Package Minimold Pinning 1 = OUT, 2 = GND, 3 = V S Dimensions (mm) 5.4 W x 6.35 H x 4.9 D Mounting Leaded Application Remote control (1) (2) (3) (4) (5) (6) Best remote control code MCIR RCMM Mitsubishi RECS-80 Code r-map XMP-1, XMP-2 Rev. 1.0, 04-Jul-16 Document Number: 82742 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 TSOP331.., TSOP333.., TSOP335.. www.vishay.com Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT 17170 5 16833-13 R 1 Transmitter 3 IR receiver with V + V S S TSALxxxx 30 k C 1 C 1 OUT V Band Demo- O Input AGC GND pass GND dulator 2 R and C are recommended for protection against EOS. 1 1 PIN Control circuit Components should be in the range of 33 < R < 1 k, 1 C > 0.1 F. 1 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +6 V S Supply current I 3mA S Output voltage V -0.3 to (V + 0.3) V O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Soldering temperature t 10 s, 1 mm from case T 260 C sd Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability. ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT E = 0, V = 3.3 V I 0.27 0.35 0.45 mA v S SD Supply current E = 40 klx, sunlight I -0.45- mA v SH Supply voltage V 2.5 - 5.5 V S E = 0, test signal see Fig. 1, v Transmission distance IR diode TSAL6200, d- 45 - m I = 150 mA F 2 I = 0.5 mA, E = 0.7 mW/m , OSL e Output voltage low V - - 100 mV OSL test signal see Fig. 1 Pulse width tolerance: 2 Minimum irradiance t - 5/f < t < t + 6/f , E - 0.08 0.15 mW/m pi 0 po pi 0 e min. test signal see Fig. 1 t - 5/f < t < t + 6/f , pi 0 po pi 0 2 Maximum irradiance E 30 - - W/m e max. test signal see Fig. 1 Angle of half transmission Directivity - 45 - deg 1/2 distance Rev. 1.0, 04-Jul-16 Document Number: 82742 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 Circuit