TSOP332.., TSOP334.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Very low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Supply voltage: 2.5 V to 5.5 V Improved immunity against ambient light Insensitive to supply voltage ripple and noise Compatible with wave or reflow soldering (see P version of Minimold option datasheets) Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 DESCRIPTION The TSOP332.. and TSOP334.. series are miniaturized IR receiver modules for infrared remote control systems. A PIN MECHNICAL DATA diode and a preamplifier are assembled on lead frame, the epoxy package contains an IR filter. Pinning for TSOP334..: The demodulated output signal can be directly connected to 1 = OUT, 2 = GND, 3 = V S a microprocessor for decoding. The TSOP334.. series devices are optimized to suppress almost all spurious pulses from energy saving lamps like CFLs. The AGC4 used in the TSOP334.. may suppress some data signals. The TSOP332.. series are provided primarily for compatibility with old AGC2 designs. New designs should prefer the TSOP334.. series containing the newer AGC4. These components have not been qualified according to automotive specifications. PARTS TABLE AGC LEGACY, FOR LONG BURSTS (AGC2) FOR LONG BURSTS, VERY NOISY ENVIRONMENTS (AGC4) 30 kHz TSOP33230 TSOP33430 33 kHz TSOP33233 TSOP33433 (1)(2)(3) 36 kHz TSOP33236 TSOP33436 Carrier (4)(5) frequency 38 kHz TSOP33238 TSOP33438 40 kHz TSOP33240 TSOP33440 (6)(7) 56 kHz TSOP33256 TSOP33456 Package Minimold Pinning 1 = OUT, 2 = GND, 3 = V S Dimensions (mm) 5.4 W x 6.35 H x 4.9 D Mounting Leaded Application Remote control (1) (2) (3) (4) (5) (6) (7) Best remote control code RC-5 RC-6 Panasonic NEC Sharp r-step Thomson RCA BLOCK DIAGRAM APPLICATION CIRCUIT 17170 5 16833-13 R 1 Transmitter 3 IR receiver with V + V S S TSALxxxx 30 k C 1 C 1 OUT Band V Demo- O Input AGC GND pass GND dulator 2 R and C are recommended for protection against EOS. 1 1 PIN Control circuit Components should be in the range of 33 < R < 1 k, 1 C > 0.1 F. 1 Rev. 1.2, 04-Jul-16 Document Number: 82663 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 Circuit TSOP332.., TSOP334.. www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +6 V S Supply current I 3mA S Output voltage V -0.3 to (V + 0.3) V O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Soldering temperature t 10 s, 1 mm from case T 260 C sd Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability. ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT E = 0, V = 3.3 V I 0.27 0.35 0.45 mA v S SD Supply current E = 40 klx, sunlight I -0.45- mA v SH Supply voltage V 2.5 - 5.5 V S E = 0, test signal see Fig. 1, v Transmission distance IR diode TSAL6200, d- 45 - m I = 150 mA F 2 I = 0.5 mA, E = 0.7 mW/m , OSL e Output voltage low V - - 100 mV OSL test signal see Fig. 1 Pulse width tolerance: 2 Minimum irradiance t - 5/f < t < t + 6/f , E - 0.08 0.15 mW/m pi 0 po pi 0 e min. test signal see Fig. 1 t - 5/f < t < t + 6/f , pi 0 po pi 0 2 Maximum irradiance E 30 - - W/m e max. test signal see Fig. 1 Angle of half transmission Directivity - 45 - deg 1/2 distance TYPICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb Optical Test Signal E e 1.0 (IR diode TSAL6200, I = 0.4 A, 30 pulses, f = f , t = 10 ms) F 0 Output pulse width 0.9 0.8 Input burst length 0.7 t 0.6 t * pi 0.5 T 0.4 * t 10/f is recommended for optimal function pi 0 0.3 Output Signal = 950 nm, 16110 V O 0.2 Optical test signal, fig. 1 1) 0.1 7/f < t < 15/f V 0 d 0 OH 2) t - 5/f < t < t + 6/f pi 0 po pi 0 0 0.1 1 10 100 1000 10 000 V OL 20743 E - Irradiance (mW/m) 1) 2) t e t t d po Fig. 1 - Output Active Low Fig. 2 - Pulse Length and Sensitivity in Dark Ambient Rev. 1.2, 04-Jul-16 Document Number: 82663 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 t - Output Pulse Width (ms) po