33 3 TSSP40..SS1XB www.vishay.com Vishay Semiconductors IR Receiver Module for Light Barrier Systems FEATURES Constant gain for consistent results under any lighting condition Up to 1 m for presence sensing PIN diode and sensor IC in one package Low supply current Shielding against EMI Visible light is suppressed by IR filter 1 22 Insensitive to supply voltage ripple and noise 33 16672 Supply voltage: 2.5 V to 5.5 V Material categorization: for definitions of compliance DESIGN SUPPORT TOOLS AVAILABLE please see www.vishay.com/doc 99912 3D Models APPLICATIONS Reflective sensors for hand dryers, towel or soap MECHANICAL DATA dispensers, water faucets, toilet flush Pinning: Vending machine fall detection 1 = OUT, 2 = GND, 3 = V S Security and pet gates Person or object vicinity activation DESCRIPTION The TSSP40..SS1XB are compact infrared detector modules for presence sensing applications. They provide an active low output in response to infrared bursts at 940 nm. The TSSP40..SS1XB are 20 x less sensitive than the TSSP40.., for ease of use in reflective applications at less than 1 m range where high sensitivity is not needed an d can complicate the design. This component has not been qualified to automotive specifications. PARTS TABLE 38 kHz TSSP4038SS1XB Carrier frequency 56 kHz TSSP4056SS1XB Package Mold Pinning 1 = OUT, 2 = GND, 3 = V S Dimensions (mm) 6.0 W x 6.95 H x 5.6 D Mounting Leaded Application Presence sensors BLOCK DIAGRAM PRESENCE SENSING 16833 8 +3 V 3 IR emitter V S 33 k Envelope 1 signal OUT e.g. 38 kHz Band Demo- Input AMP pass dulator +3 V 2 Out to C PIN GND Rev. 1.5, 10-Apr-2019 Document Number: 82737 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 DD D TSSP40..SS1XB www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage (pin 3) V -0.3 to +6.0 V S Supply current (pin 3) I 5mA S Output voltage (pin 1) V -0.3 to 5.5 V O Voltage at output to supply V - V -0.3 to (V + 0.3) V S O S Output current (pin 1) I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Soldering temperature t 10 s, 1 mm from case T 260 C sd Power consumption T 85 C P 10 mW amb tot Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating onl y and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specificatio n is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT E = 0, V = 5 V I 0.55 0.7 0.9 mA v S SD Supply current (pin 3) E = 40 klx, sunlight I -0.8 - mA v SH Supply voltage V 2.5 - 5.5 V S E = 0, test signal see Fig. 1, v Transmission distance IR diode TSAL6200, d- 2.4 - m I = 50 mA F 2 I = 0.5 mA, E = 2 mW/m , OSL e Output voltage low (pin 1) V - - 100 mV OSL test signal see Fig. 1 Pulse width tolerance: 2 Minimum irradiance t - 5/f < t < t + 6/f , E -7 14 mW/m pi 0 po pi 0 e min. test signal see Fig. 1 t - 5/f < t < t + 6/f , pi 0 po pi 0 2 Maximum irradiance E 50 - - W/m e max. test signal see Fig. 1 Angle of half transmission Directivity - 45 - deg 1/2 distance TYPICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb 1.4 Optical Test Signal E e (IR diode TSAL6200, I = 0.4 A, 30 pulses, f = f , t = 10 ms) F 0 1.2 Ouput pulse width 1.0 t 0.8 t * pi T 0.6 Input burst length * t 10/f is recommended for optimal function pi 0 0.4 Output Signal 16110 V O 1) 0.2 7/f < t < 15/f = 950 nm, V 0 d 0 OH 2) t - 5/f < t < t + 6/f optical test signal, Fig. 1 pi 0 po pi 0 0 V OL 0.1 10 1000 100 000 1) 2) t t t d po 2 E - Irradiance (mW/m ) e Fig. 1 - Output Active Low Fig. 2 - Pulse Length and Sensitivity in Dark Ambient Rev. 1.5, 10-Apr-2019 Document Number: 82737 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 t - Output Pulse Width (ms) po