TSOP361.., TSOP363.., TSOP365.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Very low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Continuous data transmission possible Supply voltage: 2.5 V to 5.5 V Insensitive to supply voltage ripple and noise 4 3 Taping available for topview and sideview 2 1 assembly 16797 Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 click logo to get started DESIGN SUPPORT TOOLS DESCRIPTION Models The TSOP361.., TSOP363.., and TSOP365.. series are Available miniaturized SMD IR receiver modules for infrared remote control systems. PIN diode and preamplifier are assembled MECHANICAL DATA on a lead frame, the epoxy package contains an IR filter. The Pinning: demodulated output signal can be directly connected to a 1 = GND, 2 = N.C., 3 = V , 4 = OUT microprocessor for decoding. S The TSOP363.. series devices are optimized to suppress ORDERING CODE almost all spurious pulses from energy saving lamps like Taping: CFLs. AGC3 may also suppress some data signals if continuously transmitted. TSOP36...TT - top view taped The TSOP361.. series are provided primarily for TSOP36...TR - side view taped compatibility with old AGC1 designs. New designs should prefer the TSOP363.. series containing the newer AGC3. The TSOP365.. series contain a very robust AGC5. This series should only be used for critically noisy environments. These components have not been qualified according to automotive specifications. PARTS TABLE LEGACY, FOR SHORT BURST NOISY ENVIRONMENTS VERY NOISY ENVIRONMENTS AGC REMOTE CONTROLS (AGC1) AND SHORT BURSTS (AGC3) AND SHORT BURSTS (AGC5) 30 kHz TSOP36130 TSOP36330 TSOP36530 33 kHz TSOP36133 TSOP36333 TSOP36533 (1) 36 kHz TSOP36136 TSOP36336 TSOP36536 Carrier frequency (2)(3)(4)(5) 38 kHz TSOP36138 TSOP36338 TSOP36538 40 kHz TSOP36140 TSOP36340 TSOP36540 56 kHz TSOP36156 TSOP36356 TSOP36556 Package Panhead Pinning 1 = GND, 2 = N.C., 3 = V , 4 = OUT S Dimensions (mm) 7.5 W x 5.3 H x 4.0 D Mounting SMD Application Remote control (1) (2) (3) (4) (5) Best choice for MCIR Mitsubishi RECS-80 Code r-map XMP-1, XMP-2 Rev. 1.6, 24-Sep-2018 Document Number: 82567 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 TSOP361.., TSOP363.., TSOP365.. www.vishay.com Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT 3 17170-11 R 1 V S Transmitter 30 k IR receiver with V + V S S 4 TSALxxxx C 1 OUT Band Demo- C Input AGC OUT dulator pass V O GND 1 2 GND PIN Control circuit GND R and C recommended to reduce supply ripple for V < 2.8 V 1 1 S 16839 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage (pin 3) V -0.3 to +6 V S Supply current (pin 3) I 3mA S Output voltage (pin 4) V -0.3 to (V + 0.3) V O S Output current (pin 4) I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT E = 0, V = 3.3 V I 0.27 0.35 0.45 mA v S SD Supply current E = 40 klx, sunlight I -0.45- mA v SH Supply voltage V 2.5 - 5.5 V S E = 0, test signal see Fig. 1, v Transmission distance d- 24 - m IR diode TSAL6200, I = 50 mA F 2 Output voltage low I = 0.5 mA, E = 0.7 mW/m , test signal see Fig. 1 V - - 100 mV OSL e OSL Pulse width tolerance: 2 Minimum irradiance E - 0.12 0.25 mW/m e min. t - 5/f < t < t + 6/f , test signal see Fig. 1 pi o po pi o 2 Maximum irradiance t - 5/f < t < t + 6/f , test signal see Fig. 1 E 30 - - W/m pi o po pi o e max. Directivity Angle of half transmission distance - 50 - 1/2 Rev. 1.6, 24-Sep-2018 Document Number: 82567 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 Circuit