TSOP381.., TSOP383.., TSOP385.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Very low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Supply voltage: 2.5 V to 5.5 V Improved immunity against ambient light Insensitive to supply voltage ripple and noise Material categorization: for definitions of compliance please see 19026 www.vishay.com/doc 99912 click logo to get started DESIGN SUPPORT TOOLS DESCRIPTION These products are miniaturized receivers for infrared remote control systems. A PIN diode and a preamplifier are Models Available assembled on a lead frame, the epoxy package contains an IR filter. The demodulated output signal can be directly MECHANICAL DATA connected to a microprocessor for decoding. Pinning for TSOP381.., TSOP383.., TSOP385..: The TSOP383.. series devices are optimized to suppress 1 = OUT, 2 = GND, 3 = V almost all spurious pulses from energy saving lamps like S CFLs. AGC3 may also suppress some data signals if continuously transmitted. The TSOP381.. series are provided primarily for compatibility with old AGC1 designs. New designs should prefer the TSOP383.. series containing the newer AGC3. The TSOP385.. series contain a very robust AGC5. This series should only be used for critically noisy environments. These components have not been qualified according to automotive specifications. PARTS TABLE LEGACY, FOR SHORT BURST NOISY ENVIRONMENTS AND VERY NOISY ENVIRONMENTS AGC REMOTE CONTROLS (AGC1) SHORT BURSTS (AGC3) AND SHORT BURSTS (AGC5) 30 kHz TSOP38130 TSOP38330 TSOP38530 33 kHz TSOP38133 TSOP38333 TSOP38533 (1)(6) 36 kHz TSOP38136 TSOP38336 TSOP38536 Carrier frequency (2)(3)(4)(5) 38 kHz TSOP38138 TSOP38338 TSOP38538 40 kHz TSOP38140 TSOP38340 TSOP38540 56 kHz TSOP38156 TSOP38356 TSOP38556 Package Minicast Pinning 1 = OUT, 2 = GND, 3 = V S Dimensions (mm) 5.0 W x 6.95 H x 4.8 D Mounting Leaded Application Remote control (1) (2) (3) (4) (5) (6) Best choice for MCIR Mitsubishi RECS-80 Code r-map XMP-1, XMP-2 RCMM Rev. 1.6, 12-Apr-18 Document Number: 81743 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 TSOP381.., TSOP383.., TSOP385.. www.vishay.com Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT 16833-13 17170-11 R 1 3 Transmitter IR receiver with V + V 30 k S S TSALxxxx C 1 1 C Band Demo- OUT Input AGC pass dulator V O GND GND 2 PIN Control circuit R and C recommended to reduce supply ripple for V < 2.8 V 1 1 S ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +6 V S Supply current I 3mA S Output voltage V -0.3 to (V + 0.3) V O S 5mA Output current I O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Soldering temperature t 10 s, 1 mm from case T 260 C sd Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT E = 0, V = 3.3 V I 0.27 0.35 0.45 mA v S SD Supply current E = 40 klx, sunlight I -0.45- mA v SH Supply voltage V 2.5 - 5.5 V S E = 0, test signal see Fig. 1, v Transmission distance d- 45 - m IR diode TSAL6200, I = 200 mA F 2 Output voltage low I = 0.5 mA, E = 0.7 mW/m , test signal see Fig. 1 V -- 100 mV OSL e OSL Pulse width tolerance: 2 Minimum irradiance E - 0.12 0.25 mW/m e min. t - 5/f < t < t + 6/f , test signal see Fig. 1 pi o po pi o 2 Maximum irradiance t - 5/f < t < t + 6/f , test signal see Fig. 1 E 30 - - W/m pi o po pi o e max. Directivity Angle of half transmission distance - 45 - deg 1/2 TYPICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb 0.40 Optical Test Signal E e (IR diode TSAL6200, I = 0.4 A, N = 6 pulses, f = f , t = 10 ms) F 0 0.35 0.30 t 0.25 Output pulse width t *) pi 0.20 T 0.15 *) t 6/f is recommended for optimal function pi 0 Input burst length Output Signal 14337 0.10 V O 1) 3/f < t < 9/f 0 d 0 0.05 = 950 nm, 2) t - 4/f < t < t + 6/f V pi 0 po pi 0 optical test signal, Fig. 1 OH 0 0.1 1 10 100 1000 10 000 100 000 V OL 1) 2) t t t d po 20771 E - Irradiance (mW/m) e Fig. 1 - Output Active Low Fig. 2 - Pulse Length and Sensitivity in Dark Ambient Rev. 1.6, 12-Apr-18 Document Number: 81743 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 t - Output Pulse Width (ms) po Circuit