333 3 TSOP61.., TSOP63.., TSOP65.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Improved immunity against HF and RF noise Low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Improved shielding against EMI Supply voltage: 2.5 V to 5.5 V 4 3 Improved immunity against ambient light 2 1 16797 Insensitive to supply voltage ripple and noise Taping available for top view and side view assembly LINKS TO ADDITIONAL RESOURCES Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 Product Page 3D Models Calculators Marking MECHANICAL DATA Pinning DESCRIPTION 1 = GND, 2 = N.C., 3 = V , 4 = OUT S The TSOP61.., TSOP63.. series are miniaturized SM D IR receivers for infrared remote control systems. A PIN diode and a preamplifier are assembled on a lead frame, the ORDERING CODE epoxy package contains an IR filter. The demodulated Taping: output signal can be directly connected to a microprocessor for decoding. TSOP6...TT - top view taped, 1190 pcs/reel The TSOP63.. series devices are optimized to suppress TSOP6...TR - side view taped, 1120 pcs/reel almost all spurious pulses from Wi-Fi and CFL sources. They may suppress some data signals if continuously BLOCK DIAGRAM transmitted. The TSOP61.. series devices are provided primarily for 3 compatibility with old AGC1 designs. New designs should V S prefer the TSOP63.. series containing the newer AGC3. Th e 33 k TSOP65.. series are useful to suppress even extreme levels 4 of optical noise, but may also suppress some data signals. Band Demo- OUT Please check compatibility with your codes. Input AGC pass dulator These components have not been qualified according to 1 automotive specifications. PIN Control circuit GND 16838-1 APPLICATION CIRCUIT 17170-11 R 1 Transmitter IR receiver with V + V S S TSALxxxx C 1 C OUT V O GND GND R and C recommended to reduce supply ripple for V < 2.8 V 1 1 S Rev. 1.7, 26-Mar-2021 Document Number: 82457 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 DDD D Circuit TSOP61.., TSOP63.., TSOP65.. www.vishay.com Vishay Semiconductors PARTS TABLE LEGACY, FOR SHORT BURST NOISY ENVIRONMENTS VERY NOISY ENVIRONMENTS AGC REMOTE CONTROLS (AGC1) AND SHORT BURSTS (AGC3) AND SHORT BURSTS (AGC5) 30 kHz TSOP6130 TSOP6330 TSOP6530 33 kHz TSOP6133 TSOP6333 TSOP6533 (1) (1) 36 kHz TSOP6136 TSOP6336 TSOP6536 Carrier frequency (2)(3)(4)(5) (2)(3)(4) 38 kHz TSOP6138 TSOP6338 TSOP6538 40 kHz TSOP6140 TSOP6340 TSOP6540 56 kHz TSOP6156 TSOP6356 TSOP6556 Package Panhead Pinning 1 = GND, 2 = N.C., 3 = V , 4 = OUT S Dimensions (mm) 7.5 W x 5.3 H x 4.0 D Mounting SMD Application Remote control (1) (2) (3) (4) (5) Best choice for MCIR Mitsubishi RECS-80 Code r-map XMP-1, XMP-2 Narrow optical filter: www.vishay.com/doc 81590 Special options Wide optical flter: www.vishay.com/doc 82726 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +6 V S Supply current I 5mA S Output voltage V -0.3 to (V + 0.3) V O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating onl y and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specificatio n is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Supply voltage V 2.5 - 5.5 V S V = 5 V, E = 0 I 0.55 0.7 0.9 mA S v SD Supply current E = 40 klx, sunlight I -0.8 - mA v SH E = 0, IR diode TSAL6200, v Transmission distance d- 18 - m I = 50 mA, test signal see Fig. 1 F 2 Output voltage low I = 0.5 mA, E = 0.7 mW/m , test signal see Fig. 1 V - - 100 mV OSL e OSL Pulse width tolerance: 2 Minimum irradiance E -0.2 0.4 mW/m e min. t - 5/f < t < t + 6/f test signal see Fig. 1 pi o po pi o, 2 Maximum irradiance t - 5/f < t < t + 6/f , test signal see Fig. 1 E 50 - - W/m pi o po pi o e max. Directivity Angle of half transmission distance - 50 - deg 1/2 Rev. 1.7, 26-Mar-2021 Document Number: 82457 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000