TSOP753.., TSOP755.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Very low supply current Photo detector and preamplifier in one package Compatible also with short burst dataformats Supply voltage: 2.5 V to 5.5 V 44 Improved immunity against ambient light 33 22 Capable of side or top view 11 Two lenses for high sensitivity and wide receiving angle Insensitive to supply voltage ripple and noise 2095320953 Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 click logo to get started DESIGN SUPPORT TOOLS DESCRIPTION Models The TSOP753.., TSOP755.. series are a two lens Available miniaturized receiver module for infrared remote control systems. One PIN diode per lens and a preamplifier are MECHANICAL DATA assembled on a leadframe, the epoxy lens cap contains an Pinning: IR filter. 1, 4 = GND, 2 = V , 3 = OUT S The TSOP753..series is optimized to suppress almost all spurious pulses from energy saving lamps like CFLs. AGC3 ORDERING CODE may also suppress some data signals if continuously Taping: transmitted. TSOP75...TT - top view taped The TSOP755.. series contain a very robust AGC5. This series should only be used for critically noisy environments. TSOP75...TR - side view taped This component has not been qualified according to automotive specifications. PARTS TABLE NOISY ENVIRONMENTS VERY NOISY ENVIRONMENTS AGC AND SHORT BURSTS (AGC3) AND SHORT BURSTS (AGC5) 30 kHz TSOP75330 TSOP75530 33 kHz TSOP75333 TSOP75533 (1) 36 kHz TSOP75336 TSOP75536 Carrier frequency (2)(3)(4)(5) 38 kHz TSOP75338 TSOP75538 40 kHz TSOP75340 TSOP75540 56 kHz TSOP75356 TSOP75556 Package Heimdall Pinning 1, 4 = GND, 2 = V , 3 = OUT S Dimensions (mm) 6.8 W x 3.0 H x 3.2 D Mounting SMD Application Remote control (1) (2) (3) (4) (5) Best choice for MCIR Mitsubishi RECS-80 Code r-map XMP-1, XMP-2 Rev. 1.9, 04-Jun-2018 Document Number: 82495 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 TSOP753.., TSOP755.. www.vishay.com Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT 2 17170-11 R 1 V Transmitter S IR receiver 30 k with V + V S S 3 TSALxxxx C 1 OUT Band Demo- C Input AGC OUT pass dulator V O 1, 4 GND GND PIN Control circuit GND R and C recommended to reduce supply ripple for V < 2.8 V 1 1 S 20445-1 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +6 V S Supply current I 3mA S Output voltage V -0.3 to (V + 0.3) V O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Supply voltage V 2.5 - 5.5 V S E = 0, V = 3.3 V I 0.27 0.35 0.45 mA v S SD Supply current E = 40 klx, sunlight I -0.45- mA v SH E = 0, test signal see Fig. 1, v Transmission distance d- 24 - m IR diode TSAL6200, I = 50 mA F 2 Output voltage low I = 0.5 mA, E = 0.7 mW/m , test signal see Fig. 1 V - - 100 mV OSL e OSL Pulse width tolerance: 2 Minimum irradiance E - 0.12 0.25 mW/m e min. t - 5/f < t < t + 6/f , test signal see Fig. 1 pi o po pi o 2 Maximum irradiance t - 5/f < t < t + 6/f , test signal see Fig. 1 E 30 - - W/m pi o po pi o e max. Directivity Angle of half transmission distance - 50 - deg 1/2 TYPICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb 0.40 Optical Test Signal E e (IR diode TSAL6200, I = 0.4 A, N = 6 pulses, f = f , t = 10 ms) F 0 0.35 0.30 Output pulse width t 0.25 t *) pi 0.20 T *) t 6/f is recommended for optimal function 0.15 pi 0 Input burst length Output Signal 14337 0.10 V O 1) 3/f < t < 9/f 0 d 0 0.05 2) = 950 nm, t - 4/f < t < t + 6/f pi 0 po pi 0 V OH optical test signal, Fig. 1 0 0.1 1 10 100 1000 10 000 V OL 1) 2) t t t d po 20760 E - Irradiance (mW/m) e Fig. 1 - Output Active Low Fig. 2 - Pulse Length and Sensitivity in Dark Ambient Rev. 1.9, 04-Jun-2018 Document Number: 82495 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 t - Output Pulse Width (ms) po Circuit