TSOP53456 Vishay

333 3 TSOP532.., TSOP534.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Improved immunity against HF and RF noise Low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Supply voltage: 2.5 V to 5.5 V Improved immunity against optical noise Insensitive to supply voltage ripple and noise Compatible with wave or reflow solderin g (see P version of Minimold option datasheets) Material categorization: for definitions of compliance 23051 please see www.vishay.com/doc 99912 ADDITIONAL RESOURCES DESCRIPTION The TSOP532.. and TSOP534.. series are miniaturized IR receiver modules for infrared remote control systems. A PIN 3D Models diode and a preamplifier are assembled on lead frame, the epoxy package contains an IR filter. The demodulated MECHANICAL DATA output signal can be directly connected to a microprocessor Pinning for TSOP53...: for decoding. 1 = OUT, 2 = GND, 3 = V S The TSOP534.. series devices are optimized to suppress almost all spurious pulses from Wi-Fi and CFL sources. They may suppress some data signals if continuously transmitted. The TSOP532.. series devices are provided primarily for compatibility with old AGC2 designs. New designs should prefer the TSOP534.. series containing the newer AGC4. These components have not been qualified according to automotive specifications. PARTS TABLE LEGACY, FOR LONG BURSTS FOR LONG BURSTS, AGC (AGC2) VERY NOISY ENVIRONMENTS (AGC4) 30 kHz TSOP53230 TSOP53430 33 kHz TSOP53233 TSOP53433 (1)(2)(3) 36 kHz TSOP53236 TSOP53436 Carrier frequency (4)(5) 38 kHz TSOP53238 TSOP53438 40 kHz TSOP53240 TSOP53440 (6)(7) 56 kHz TSOP53256 TSOP53456 Package Minimold Pinning 1 = OUT, 2 = GND, 3 = V S Dimensions (mm) 5.4 W x 6.35 H x 4.9 D Mounting Leaded Application Remote control (1) (2) (3) (4) (5) (6) (7) Best choice for RC-5 RC-6 Panasonic NEC Sharp r-step Thomson RCA Rev. 1.4, 31-Jul-2019 Document Number: 82743 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 DDD D TSOP532.., TSOP534.. www.vishay.com Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT 16833-13 17170-11 R 1 3 Transmitter IR receiver with 30 k V + V S S TSALxxxx C 1 1 C OUT Band Demo- Input AGC pass dulator V O GND GND 2 PIN Control circuit R and C recommended to reduce supply ripple for V < 2.8 V 1 1 S ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +6 V S Supply current I 5mA S Output voltage V -0.3 to 5.5 V O Voltage at output to supply V - V -0.3 to (V + 0.3) V S O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Soldering temperature t 10 s, 1 mm from case T 260 C sd Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating onl y and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specificatio n is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT E = 0, V = 5 V I 0.55 0.7 0.9 mA v S SD Supply current E = 40 klx, sunlight I -0.8 - mA v SH Supply voltage V 2.5 - 5.5 V S E = 0, test signal see Fig. 1, v Transmission distance IR diode TSAL6200, d- 24 - m I = 50 mA F 2 I = 0.5 mA, E = 0.7 mW/m , OSL e Output voltage low V - - 100 mV OSL test signal see Fig. 1 Pulse width tolerance: 2 Minimum irradiance t - 5/f < t < t + 6/f , E - 0.12 0.25 mW/m pi o po pi o e min. test signal see Fig. 1 t - 5/f < t < t + 6/f , pi o po pi o 2 Maximum irradiance E 50 - - W/m e max. test signal see Fig. 1 Angle of half transmission Directivity - 45 - deg 1/2 distance Rev. 1.4, 31-Jul-2019 Document Number: 82743 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 Circuit