333 3 TSOP531.., TSOP533.., TSOP535.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Improved immunity against HF and RF noise Low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Supply voltage: 2.5 V to 5.5 V Improved immunity against optical noise Insensitive to supply voltage ripple and noise Compatible with wave or reflow solderin g (see P version of Minimold option datasheets) Material categorization: for definitions of compliance 23051 please see www.vishay.com/doc 99912 LINKS TO ADDITIONAL RESOURCES MECHANICAL DATA Pinning for TSOP53...: Product Page 3D Models Calculators Marking Packages 1 = OUT, 2 = GND, 3 = V S Holders Bends and Cuts ORDERING CODE TSOP53... - 1800 pieces in bags DESCRIPTION The TSOP531.., TSOP533.., and TSOP535.. series are BLOCK DIAGRAM miniaturized IR receiver modules for infrared remote control 16833-13 systems. A PIN diode and a preamplifier are assembled on 3 lead frame, the epoxy package contains an IR filter. The demodulated output signal can be directly connected to a 30 k microprocessor for decoding. 1 The TSOP533.. series devices are optimized to suppress Band almost all spurious pulses from Wi-Fi and CFL sources. Demo- Input AGC pass dulator They may suppress some data signals if continuously transmitted. 2 The TSOP531.. series devices are provided primarily for PIN Control circuit compatibility with old AGC1 designs. New designs should prefer the TSOP533.. series containing the newer AGC3. The TSOP535.. series are useful to suppress even extrem e levels of optical noise, but may also suppress some data APPLICATION CIRCUIT signals. Please check compatibility with your codes. 17170-11 These components have not been qualified according to R 1 automotive specifications. Transmitter IR receiver with V + V S S TSALxxxx C 1 C OUT V O GND GND R and C recommended to reduce supply ripple for V < 2.8 V 1 1 S Rev. 1.6, 30-Jul-2021 Document Number: 82745 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 DDD D Circuit TSOP531.., TSOP533.., TSOP535.. www.vishay.com Vishay Semiconductors PARTS TABLE LEGACY, FOR SHORT BURSTS FOR SHORT BURSTS, NOISY FOR SHORT BURSTS, VERY AGC (AGC1) ENVIRONMENTS (AGC3) NOISY ENVIRONMENTS (AGC5) 30 kHz TSOP53130 TSOP53330 TSOP53530 33 kHz TSOP53133 TSOP53333 TSOP53533 (1) 36 kHz TSOP53136 TSOP53336 TSOP53536 Carrier frequency (2)(3)(4)(5) 38 kHz TSOP53138 TSOP53338 TSOP53538 40 kHz TSOP53140 TSOP53340 TSOP53540 56 kHz TSOP53156 TSOP53356 TSOP53556 Package Minimold Pinning 1 = OUT, 2 = GND, 3 = V S Dimensions (mm) 5.4 W x 6.35 H x 4.9 D Mounting Leaded Application Remote control (1) (2) (3) (4) (5) Best choice for MCIR Mitsubishi RECS-80 Code r-map XMP-1 Narrow optical filter: www.vishay.com/doc 81590 Special options Wide optical flter: www.vishay.com/doc 82726 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +6 V S Supply current I 5mA S Output voltage V -0.3 to 5.5 V O Voltage at output to supply V - V -0.3 to (V + 0.3) V S O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Soldering temperature t 10 s, 1 mm from case T 260 C sd Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating onl y and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specificatio n is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT E = 0, V = 5 V I 0.55 0.7 0.9 mA v S SD Supply current E = 40 klx, sunlight I -0.8 - mA v SH Supply voltage V 2.5 - 5.5 V S E = 0, test signal see Fig. 1, v Transmission distance d- 24 - m IR diode TSAL6200, I = 50 mA F 2 I = 0.5 mA, E = 0.7 mW/m , OSL e Output voltage low V - - 100 mV OSL test signal see Fig. 1 Pulse width tolerance: 2 Minimum irradiance t - 5/f < t < t + 6/f , E - 0.12 0.25 mW/m pi o po pi o e min. test signal see Fig. 1 t - 5/f < t < t + 6/f , pi o po pi o 2 Maximum irradiance E 50 - - W/m e max. test signal see Fig. 1 Angle of half transmission Directivity - 45 - deg 1/2 distance Rev. 1.6, 30-Jul-2021 Document Number: 82745 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000