TSOP57438TT1 Vishay

333 3 TSOP572.., TSOP574.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Improved immunity against HF and RF noise Height of 0.8 mm 75 half angle sensitivity Low supply current Photo detectors and preamplifier in one package Internal filter for PCM frequency Supply voltage: 2.5 V to 5.5 V, typically even 2.0 V to 5.5 V is possible Improved immunity against optical noise Insensitive to supply voltage ripple and noise Material categorization: for definitions of compliance 22531-1 please see www.vishay.com/doc 99912 LINKS TO ADDITIONAL RESOURCES ORDERING CODE Taping: Product Page 3D Models Calculators Marking TSOP57...TT1 - top view taped, 1800 pcs/reel BLOCK DIAGRAM DESCRIPTION The TSOP57... series are miniaturized SMD IR receiver 4, 5 modules for infrared remote control systems. A PIN diode V S and a preamplifier are assembled on a PCB, the epoxy 33 k package contains an IR filter. 1 The demodulated output signal can be directly connected to OUT Demo- Band a microprocessor for decoding. Input AGC pass dulator The TSOP574.. series devices are optimized to suppress 2, 3, 6, 7, 8 almost all spurious pulses from Wi-Fi and CFL sources. They may suppress some data signals if continuously PIN GND Control circuit transmitted. 20445-6 The TSOP572.. series devices are provided primarily for compatibility with old AGC2 designs. New designs should prefer the TSOP574.. series containing the newer AGC4. APPLICATION CIRCUIT These components have not been qualified according to automotive specifications. 17170-11 R 1 Transmitter IR receiver with V + V S S TSALxxxx C 1 C OUT V O GND GND R and C recommended to reduce supply ripple for V < 2.8 V 1 1 S Rev. 2.7, 30-Mar-2021 Document Number: 82434 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 DDD D Circuit TSOP572.., TSOP574.. www.vishay.com Vishay Semiconductors PARTS TABLE LEGACY, FOR RECOMMENDED FOR AGC LONG BURST REMOTE CONTROLS (AGC2) LONG BURST CODES (AGC4) (1)(2)(3) 36 kHz TSOP57236 TSOP57436 (4)(5) 38 kHz TSOP57238 TSOP57438 Carrier frequency 40 kHz TSOP57240 TSOP57440 (6)(7) 56 kHz TSOP57256 TSOP57456 Package Belobog Pinning 1 = OUT, 2, 3, 6, 7, 8 = GND, 4, 5 = V S Dimensions (mm) 3.95 W x 3.95 H x 0.8 D Mounting SMD Application Remote control (1) (2) (3) (4) (5) (6) (7) Best choice for RC-5 RC-6 Panasonic NEC Sharp r-step Thomson RCA Special options Extended temperature range: www.vishay.com/doc 82738 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +6 V S Supply current I 5mA S Output voltage V -0.3 to (V + 0.3) V O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating onl y and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specificatio n is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Supply voltage V 2.5 - 5.5 V S V = 5 V, E = 0 I 0.55 0.7 0.9 mA S v SD Supply current E = 40 klx, sunlight I -0.8 - mA v SH E = 0, v IR diode TSAL6200, Transmission distance d- 18 - m I = 50 mA, F test signal see Fig. 1 2 I = 0.5 mA, E = 0.7 mW/m , OSL e Output voltage low V - - 100 mV OSL test signal see Fig. 1 Pulse width tolerance: 2 Minimum irradiance t - 5/f < t < t + 6/f E -0.2 0.4 mW/m pi o po pi o, e min. test signal see Fig. 1 t - 5/f < t < t + 6/f , pi o po pi o 2 Maximum irradiance E 50 - - W/m e max. test signal see Fig. 1 Angle of Directivity - 75 - deg 1/2 half transmission distance Rev. 2.7, 30-Mar-2021 Document Number: 82434 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000