TSOP593.., TSOP595.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES 4 3 Improved immunity against HF and RF noise 2 1 Low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Supply voltage: 2.5 V to 5.5 V Improved immunity against ambient light Two lenses for high sensitivity Insensitive to supply voltage ripple and noise Ultra small top-view PCB footprint Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 22963 DESCRIPTION click logo to get started The TSOP59... series are miniaturized receiver modules for DESIGN SUPPORT TOOLS infrared remote control systems. Two PIN diodes and a preamplifier are assembled on a leadframe, the epoxy Models package contains an IR filter. The demodulated output Available signal can be directly connected to digital circuitry for decoding. MECHANICAL DATA The TSOP593.. series devices are optimized to suppress Pinning: almost all spurious pulses from Wi-Fi and energy saving 1, 4 = GND, 2 = V , 3 = OUT S lamps (CFLs). They may also suppress some data signals if continuously transmitted. The TSOP595.. series contains a very robust AGC5. This series should only be used for critically noisy environments. Please check compatibility with your codes. These components have not been qualified according to automotive specifications. PARTS TABLE NOISY ENVIRONMENTS VERY NOISY ENVIRONMENTS AGC AND SHORT BURSTS (AGC3) AND SHORT BURSTS (AGC5) 30 kHz TSOP59330 TSOP59530 33 kHz TSOP59333 TSOP59533 (1) 36 kHz TSOP59336 TSOP59536 Carrier frequency (2)(3)(4)(5) 38 kHz TSOP59338 TSOP59538 40 kHz TSOP59340 TSOP59540 56 kHz TSOP59356 TSOP59556 Package TVCast Pinning 1, 4 = GND, 2 = V , 3 = OUT S Dimensions (mm) 6.8 W x 2.6 H x 5.3 D Mounting Leaded Application Remote control (1) (2) (3) (4) (5) Best choice for MCIR Mitsubishi RECS-80 Code r-map XMP-1 Rev. 1.3, 26-Sep-2018 Document Number: 82776 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 TSOP593.., TSOP595.. www.vishay.com Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT 2 17170-11 R 1 V Transmitter S IR receiver 30 k with V + V S S 3 TSALxxxx C 1 OUT Band Demo- C Input AGC OUT pass dulator V O 1, 4 GND GND PIN GND Control circuit R and C recommended to reduce supply ripple for V < 2.8 V 1 1 S 20445-1 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +6 V S Supply current I 5mA S Output voltage V -0.3 to 5.5 V O Voltage at output to supply V - V -0.3 to (V + 0.3) V S O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Soldering temperature t 10 s, 1 mm from case T 260 C sd Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT E = 0, V = 5 V I 0.55 0.7 0.9 mA v S SD Supply current E = 40 klx, sunlight I -0.8 - mA v SH Supply voltage V 2.5 - 5.5 V S Transmission distance E = 0, test signal see Fig. 1, IR diode TSAL6200, I = 50 mA d - 18 - m v F 2 Output voltage low I = 0.5 mA, E = 0.7 mW/m , test signal see Fig. 1 V - - 100 mV OSL e OSL 2 Minimum irradiance Pulse width tolerance: t - 5/f < t < t + 6/f , test signal see Fig. 1 E -0.2 0.4 mW/m pi o po pi o e min. 2 Maximum irradiance t - 5/f < t < t + 6/f , test signal see Fig. 1 E 50 - - W/m pi o po pi o e max. Directivity Angle of half transmission distance - 45 - deg 1/2 TYPICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb Optical Test Signal 0.5 E e (IR diode TSAL6200, I = 0.4 A, N = 6 pulses, f = f , t = 10 ms) F 0 = 950 nm, optical test signal, Fig. 1 0.4 t t *) pi 0.3 Output pulse width T *) t 6/f is recommended for optimal function pi 0 0.2 Output Signal 14337 Input burst length V O 1) 3/f < t < 9/f 0 d 0 0.1 2) t - 4/f < t < t + 6/f V pi 0 po pi 0 OH 0 V OL 1) 2) t t t d po 0.1 10 1000 100 000 2 E - Irradiance (mW/m ) e Fig. 1 - Output Active Low Fig. 2 - Pulse Length and Sensitivity in Dark Ambient Rev. 1.3, 26-Sep-2018 Document Number: 82776 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 t - Output Pulse Width (ms) po Circuit