TSOP592.., TSOP594.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES 4 3 Improved immunity against HF and RF noise 2 1 Low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Supply voltage: 2.5 V to 5.5 V Improved immunity against ambient light Two lenses for high sensitivity Insensitive to supply voltage ripple and noise Ultra small top-view PCB footprint Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 DESCRIPTION The TSOP59... series are miniaturized receiver modules for 22963 infrared remote control systems. Two PIN diodes and a preamplifier are assembled on a leadframe, the epoxy click logo to get started DESIGN SUPPORT TOOLS package contains an IR filter. The demodulated output signal can be directly connected to digital circuitry for decoding. Models Available The TSOP594.. series devices are optimized to suppress almost all spurious pulses from Wi-Fi and CFL sources. MECHANICAL DATA They may suppress some data signals if continuously transmitted. Pinning: The TSOP592.. series devices are provided primarily for 1, 4 = GND, 2 = V , 3 = OUT S compatibility with old AGC2 designs. New designs should prefer the TSOP594.. series containing the newer AGC4. These components have not been qualified according to automotive specifications. PARTS TABLE NOISY ENVIRONMENTS VERY NOISY ENVIRONMENTS AGC AND LONG BURSTS (AGC2) AND LONG BURSTS (AGC4) 30 kHz TSOP59230 TSOP59430 33 kHz TSOP59233 TSOP59433 (1)(2)(3) 36 kHz TSOP59236 TSOP59436 Carrier (4)(5) frequency 38 kHz TSOP59238 TSOP59438 40 kHz TSOP59240 TSOP59440 (6)(7) 56 kHz TSOP59256 TSOP59456 Package TVCast Pinning 1, 4 = GND, 2 = V , 3 = OUT S Dimensions (mm) 6.8 W x 2.6 H x 5.3 D Mounting Leaded Application Remote control (1) (2) (3) (4) (5) (6) (7) Best choice for RC-5 RC-6 Panasonic NEC Sharp r-step Thomson RCA BLOCK DIAGRAM APPLICATION CIRCUIT 2 17170-11 R 1 V S Transmitter IR receiver 30 k with V + V S S 3 TSALxxxx C 1 OUT Band Demo- C Input AGC dulator OUT pass V O 1, 4 GND GND PIN Control circuit GND R and C recommended to reduce supply ripple for V < 2.8 V 1 1 S 20445-1 Rev. 1.3, 26-Sep-2018 Document Number: 82779 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 Circuit TSOP592.., TSOP594.. www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +6 V S Supply current I 5mA S Output voltage V -0.3 to 5.5 V O Voltage at output to supply V - V -0.3 to (V + 0.3) V S O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Soldering temperature t 10 s, 1 mm from case T 260 C sd Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT E = 0, V = 5 V I 0.55 0.7 0.9 mA v S SD Supply current E = 40 klx, sunlight I -0.8 - mA v SH Supply voltage V 2.5 - 5.5 V S E = 0, test signal see Fig. 1, v Transmission distance d- 18 - m IR diode TSAL6200, I = 50 mA F 2 Output voltage low I = 0.5 mA, E = 0.7 mW/m , test signal see Fig. 1 V - - 100 mV OSL e OSL Pulse width tolerance: 2 Minimum irradiance E -0.2 0.4 mW/m e min. t - 5/f < t < t + 6/f , test signal see Fig. 1 pi o po pi o 2 Maximum irradiance t - 5/f < t < t + 6/f , test signal see Fig. 1 E 50 - - W/m pi o po pi o e max. Directivity Angle of half transmission distance - 45 - deg 1/2 TYPICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb Optical Test Signal E e 1.0 (IR diode TSAL6200, I = 0.4 A, 30 pulses, f = f , t = 10 ms) F 0 Output pulse width 0.9 0.8 Input burst length 0.7 t 0.6 t * pi 0.5 T 0.4 * t 10/f is recommended for optimal function pi 0 0.3 Output Signal 16110 V O 0.2 = 950 nm, 1) 0.1 optical test signal, fig.1 7/f < t < 15/f V 0 d 0 OH 2) t - 5/f < t < t + 6/f pi 0 po pi 0 0 2 3 4 0.1 1 10 10 10 10 V OL 2 E - Irradiance (mW/m ) 1) 2) t e t t d po Fig. 1 - Output Active Low Fig. 2 - Pulse Length and Sensitivity in Dark Ambient Rev. 1.3, 26-Sep-2018 Document Number: 82779 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 t - Output Pulse Width (ms) po