TSOP75236WTT Vishay

TSOP752..W, TSOP754..W www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Very low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Supply voltage: 2.5 V to 5.5 V Improved immunity against ambient light Capable of side or top view Low profile 2.35 mm Insensitive to supply voltage ripple and noise Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 DESCRIPTION The TSOP75...W series are miniaturized SMD IR receiver click logo to get started DESIGN SUPPORT TOOLS modules for infrared remote control systems. Two PIN diodes and a preamplifier are assembled on a leadframe, the Models epoxy package contains an IR filter. Available The demodulated output signal can be directly connected to a microprocessor for decoding. MECHANICAL DATA The TSOP754..W series devices are optimized to suppress Pinning: almost all spurious pulses from energy saving lamps like 1, 4 = GND, 2 = V , 3 = OUT S CFLs. The AGC4 used in the TSOP754..W may suppress some data signals. The TSOP752..W series are provided ORDERING CODE primarily for compatibility with old AGC2 designs. New Taping: designs should prefer the TSOP754..W series containing the newer AGC4. TSOP75...WTT - top view taped These components have not been qualified according to TSOP75...WTR - side view taped automotive specifications. PARTS TABLE LEGACY, FOR RECOMMENDED FOR AGC LONG BURST REMOTE CONTROLS (AGC2) LONG BURST CODES (AGC4) 30 kHz TSOP75230W TSOP75430W 33 kHz TSOP75233W TSOP75433W (1)(2)(3) 36 kHz TSOP75236W TSOP75436W Carrier frequency (4)(5) 38 kHz TSOP75238W TSOP75438W 40 kHz TSOP75240W TSOP75440W (6)(7) 56 kHz TSOP75256W TSOP75456W Package Heimdall no lens Pinning 1, 4 = GND, 2 = V , 3 = OUT S Dimensions (mm) 6.8 W x 3.0 H x 2.35 D Mounting SMD Application Remote control (1) (2) (3) (4) (5) (6) (7) Best choice for RC-5 RC-6 Panasonic NEC Sharp r-step Thomson RCA Rev. 2.0, 04-Jun-2018 Document Number: 82496 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 TSOP752..W, TSOP754..W www.vishay.com Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT 2 17170-11 R 1 V S Transmitter IR receiver 30 k with V + V S S 3 TSALxxxx C 1 OUT Band Demo- C Input AGC OUT pass dulator V O 1, 4 GND GND PIN Control circuit GND and C recommended to reduce supply ripple for V < 2.8 V R 1 1 S 20445-1 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +6 V S Supply current I 3mA S Output voltage V -0.3 to (V + 0.3) V O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Supply voltage V 2.5 - 5.5 V S E = 0, V = 3.3 V I 0.27 0.35 0.45 mA v S SD Supply current E = 40 klx, sunlight I -0.45- mA v SH E = 0, test signal see Fig. 1, v Transmission distance d- 16 - m IR diode TSAL6200, I = 50 mA F 2 Output voltage low I = 0.5 mA, E = 0.7 mW/m , test signal see Fig. 1 V - - 100 mV OSL e OSL Pulse width tolerance: 2 Minimum irradiance E - 0.25 0.5 mW/m e min. t - 5/f < t < t + 6/f , test signal see Fig. 1 pi o po pi o 2 Maximum irradiance t - 5/f < t < t + 6/f , test signal see Fig. 1 E 30 - - W/m pi o po pi o e max. Directivity Angle of half transmission distance - 75 - deg 1/2 TYPICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb Optical Test Signal E 1.0 e (IR diode TSAL6200, I = 0.4 A, 30 pulses, f = f , t = 10 ms) Output Pulse Width F 0 0.9 0.8 Input Burst Length 0.7 t 0.6 t * pi 0.5 T 0.4 * t 10/f is recommended for optimal function pi 0 0.3 Output Signal 16110 = 950 nm, V O 0.2 Optical Test Signal, Fig.1 1) 7/f < t < 15/f V 0 d 0 0.1 OH 2) t - 5/f < t < t + 6/f pi 0 po pi 0 0 2 3 4 5 0.1 1 10 10 10 10 10 V OL 1) 2) t t t 21583 E - Irradiance (mW/m) d po e Fig. 1 - Output Active Low Fig. 2 - Pulse Length and Sensitivity in Dark Ambient Rev. 2.0, 04-Jun-2018 Document Number: 82496 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 t - Output Pulse Width (ms) po Circuit