333 3 TSOP773.., TSOP775.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Improved immunity against HF and RF noise Continuous data transmission possible Low supply current Photo detector and preamplifier in one package 44 Internal filter for PCM frequency 33 Supply voltage: 2.5 V to 5.5 V 22 11 Improved immunity against ambient light Capable of side or top view Insensitive to supply voltage ripple and noise Two lenses for high sensitivity and wide receiving angle 2092095353 Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 LINKS TO ADDITIONAL RESOURCES MECHANICAL DATA Product Page 3D Models Calculators Marking Pinning: 1, 4 = GND, 2 = V , 3 = OUT S DESCRIPTION The TSOP773.., TSOP775.. series are a two lens ORDERING CODE miniaturized receiver module for infrared remote control Taping: systems. One PIN diode per lens and a preamplifier are TSOP77...TT - top view taped, 2200 pcs/reel assembled on a leadframe, the epoxy lens cap contains an TSOP77...TR - side view taped, 2300 pcs/reel IR filter. The TSOP773.. series devices are optimized to suppress almost all spurious pulses from Wi-Fi and CFL sources. BLOCK DIAGRAM They may suppress some data signals if continuously 2 transmitted. V S New designs should prefer the TSOP773.. series containing 30 k the newer AGC3. The TSOP775.. series are useful to 3 suppress even extreme levels of optical noise, but may also OUT Band Demo- suppress some data signals. Please check compatibility Input AGC pass dulator with your codes. 1, 4 These components have not been qualified according to PIN GND Control circuit automotive specifications. 20445-1 APPLICATION CIRCUIT 17170-11 R 1 Transmitter IR receiver with V + V S S TSALxxxx C 1 C OUT V O GND GND R and C recommended to reduce supply ripple for V < 2.8 V 1 1 S Rev. 2.0, 29-Mar-2021 Document Number: 82465 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 DDD D Circuit TSOP773.., TSOP775.. www.vishay.com Vishay Semiconductors PARTS TABLE NOISY ENVIRONMENTS VERY NOISY ENVIRONMENTS AGC AND SHORT BURSTS (AGC3) AND SHORT BURSTS (AGC5) 30 kHz TSOP77330 TSOP77530 33 kHz TSOP77333 TSOP77533 (1) 36 kHz TSOP77336 TSOP77536 Carrier frequency (2)(3)(4)(5) 38 kHz TSOP77338 TSOP77538 40 kHz TSOP77340 TSOP77540 56 kHz TSOP77356 TSOP77556 Package Heimdall Pinning 1, 4 = GND, 2 = V , 3 = OUT S Dimensions (mm) 6.8 W x 3.0 H x 3.2 D Mounting SMD Application Remote control (1) (2) (3) (4) (5) Best choice for MCIR Mitsubishi RECS-80 Code r-map XMP-1, XMP-2 Extended temperature range: www.vishay.com/doc 82738 Special options Narrow optical filter: www.vishay.com/doc 81590 Wide optical flter: www.vishay.com/doc 82726 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +6 V S Supply current I 5mA S Output voltage V -0.3 to 5.5 V O Voltage at output to supply V - V -0.3 to (V + 0.3) V S O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Soldering temperature t 10 s, 1 mm from case T 260 C sd Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating onl y and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specificatio n is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Supply voltage V 2.5 - 5.5 V S V = 5 V, E = 0 I 0.55 0.7 0.9 mA S v SD Supply current E = 40 klx, sunlight I -0.8 - mA v SH E = 0, IR diode TSAL6200, I = 50 mA, v F Transmission distance d- 18 - m test signal see Fig. 1 2 Output voltage low I = 0.5 mA, E = 0.7 mW/m , test signal see Fig. 1 V - - 100 mV OSL e OSL Pulse width tolerance: 2 Minimum irradiance E -0.2 0.4 mW/m e min. t - 5/f < t < t + 6/f test signal see Fig. 1 pi o po pi o, 2 Maximum irradiance t - 5/f < t < t + 6/f , test signal see Fig. 1 E 50 - - W/m pi o po pi o e max. Directivity Angle of half transmission distance - 50 - 1/2 Rev. 2.0, 29-Mar-2021 Document Number: 82465 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000