TSOP96338TR Vishay

333 3 TSOP963.., TSOP965.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Improved dark sensitivity Improved immunity against optical noise Very low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Supply voltage: 2.0 V to 3.6 V 4 3 Insensitive to supply voltage ripple and noise 2 1 16797 Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 LINKS TO ADDITIONAL RESOURCES MECHANICAL DATA Product Page 3D Models Calculators Marking 1 = GND, 2 = N.C., 3 = V , 4 = OUT S ORDERING CODE DESCRIPTION Taping: The TSOP96... series devices are the latest generation TSOP96...TT - top view taped, 1190 pcs/reel miniaturized IR receiver modules for infrared remote control systems. These series provide improvements in sensitivity TSOP96...TR - side view taped, 1120 pcs/reel to remote control signals in dark ambient as well as in sensitivity in the presence of optical disturbances e.g. from CFLs. BLOCK DIAGRAM The devices contain a PIN diode and a preamplifier 3 assembled on a lead frame. The epoxy package contains an V S IR filter. The demodulated output signal can be directly 30 k connected to a microprocessor for decoding. 4 The TSOP963.. and TSOP965.., series devices are designed OUT Band Demo- to receive short burst codes (6 or more carrier cycles per Input AGC pass dulator burst). The third digit designates the AGC level (AGC3 or AGC5) and the last two digits designate the band-pass 1 2 frequency (see table below). The higher the AGC, the better PIN Control circuit GND noise is suppressed, but the lower the code compatibility. AGC3 provides enhanced noise suppression and AGC5 16839 provides maximized noise suppression. Generally, we advise to select the highest AGC that satisfactorily receives the desired remote code. APPLICATION CIRCUIT These components have not been qualified to automotive 17170-12 R specifications. 1 Transmitter IR receiver with V + V S S TSALxxxx C 1 C OUT V O GND GND R and C recommended to reduce supply ripple for V < 2.2 V 1 1 S Rev. 1.1, 26-Mar-2021 Document Number: 82848 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 DDD D Circuit TSOP963.., TSOP965.. www.vishay.com Vishay Semiconductors PARTS TABLE ENHANCED NOISE SUPPRESSION MAXIMIZED NOISE SUPPRESSION AGC (AGC3) (AGC5) 30 kHz TSOP96330 TSOP96530 33 kHz TSOP96333 TSOP96533 (1) 36 kHz TSOP96336 TSOP96536 Carrier frequency (2)(4) 38 kHz TSOP96338 TSOP96538 40 kHz TSOP96340 TSOP96540 (3) 56 kHz TSOP96356 TSOP96556 Package Panhead Pinning 1 = GND, 2 = N.C., 3 = V , 4 = OUT S Dimensions (mm) 7.5 W x 5.3 H x 4.0 D Mounting SMD Application Remote control (1) (2) (3) (4) Best choice for RCMM RECS-80 Code r-map XMP-1, XMP-2 Narrow optical filter: www.vishay.com/doc 81590 Special options Wide optical flter: www.vishay.com/doc 82726 Note 30 kHz and 33 kHz only available on written request ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +3.6 V S Supply current I 3mA S Output voltage V -0.3 to (V + 0.3) V O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating onl y and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specificatio n is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT E = 0, V = 3.3 V I 0.25 0.37 0.45 mA v S SD Supply current E = 40 klx, sunlight I -0.50 - mA v SH Supply voltage V 2.0 - 3.6 V S E = 0, test signal see Fig. 1, v Transmission distance d- 24 - m IR diode TSAL6200, I = 50 mA F 2 I = 0.5 mA, E = 0.7 mW/m , OSL e Output voltage low V - - 100 mV OSL test signal see Fig. 1 2 Test signal: XMP code E - 0.16 0.35 mW/m e min. Minimum irradiance 2 Test signal: NEC code E - 0.12 0.30 mW/m e min. t - 3.0/f < t < t + 3.5/f , pi 0 po pi 0 2 Maximum irradiance E 30 - - W/m e max. test signal see Fig. 1 Angle of half transmission Directivity - 50 - 1/2 distance Rev. 1.1, 26-Mar-2021 Document Number: 82848 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000