VEMI65AC-HCI www.vishay.com Vishay Semiconductors 6-Channel EMI-Filter with ESD-Protection FEATURES Ultra compact LLP2513-13L package Low package profile of 0.6 mm 12 11 10 9 8 7 6-channel EMI-filter 13 Low leakage current Line resistance R = 100 S 1 2 3 4 5 6 20378 Typical cut off frequency f = 240 MHz 3dB ESD-protection acc. IEC 61000-4-2 21839 10 kV contact discharge 12 kV air discharge e4 - precious metal (e.g. Ag, Au, NiPd, NiPdAu) (no Sn) MARKING (example only) Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 YYXX 20720 Dot = pin 1 marking YY = type code (see table below) XX = date code click logo to get started DESIGN SUPPORT TOOLS Models Available ORDERING INFORMATION TAPED UNITS PER REEL DEVICE NAME ORDERING CODE MINIMUM ORDER QUANTITY (8 mm TAPE ON 7 REEL) VEMI65AC-HCI VEMI65AC-HCI-GS08 3000 15 000 PACKAGE DATA PACKAGE TYPE MOLDING COMPOUND MOISTURE DEVICE NAME WEIGHT SOLDERING CONDITIONS NAME CODE FLAMMABILITY RATING SENSITIVITY LEVEL MSL level 1 VEMI65AC-HCI LLP2513-13L 9T 5.5 mg UL 94 V-0 Peak temperature max. 260 C (according J-STD-020) ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITIONS SYMBOL VALUE UNIT All I/O pin to pin 13 acc. IEC 61000-4-5 Peak pulse current I 2A PPM t = 8/20 s single shot p Contact discharge acc. IEC 61000-4-2 10 pulses 10 ESD immunity V kV ESD Air discharge acc. IEC 61000-4-2 10 pulses 12 Operating temperature Junction temperature T -40 to +125 C J Storage temperature T -55 to +150 C STG Rev. 1.8, 09-Jan-2019 Document Number: 81680 1 For technical questions, contact: EMIFilter vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 VEMI65AC-HCI www.vishay.com Vishay Semiconductors APPLICATION NOTE With the VEMI65AC-HCI 6 different signal or data lines can be filtered and clamped to ground. Due to the different clamping levels in forward and reverse direction the clamping behaviour is Bidirectional and Asymmetric (BiAs). L1 L1OUT IN 1 12 L2 L2IN OUT 2 11 L3 L3OUT IN 3 10 13 L4 L4OUT IN 4 9 L5 L5 IN OUT 5 8 L6 L6 IN OUT 6 7 20379 The 6 independent EMI-filter are placed between pin 1 and pin 12, pin 2 and pin 11, pin 3 and pin 10, pin 4 and pin 9, pin 5 and pin 8 and pin 6 and pin 7. They all are connected to a common ground pin 13 on the backside of the package. The circuit diagram of one EMI-filter-channel shows two identical Z-diodes at the input to ground and the output to ground. These Z-diodes are characterized by the breakthrough voltage level (V ) and the diode capacitance (C ). Below the BR D breakthrough voltage level the Z-diodes can be considered as capacitors. Together with these capacitors and the line resistance R between input and output the device works as a low pass filter. Low frequency signals (f < f ) pass the filter S 3dB while high frequency signals (f > f ) will be shorted to ground through the diode capacitances C . 3dB D R S In Out (pin 1, 2, 3, 4, 5, 6) (pin 7, 8, 9, 10, 11, 12) CC C DD D GND 20380 (pin 13) Each filter is symmetrical so that both ports can be used as input or output. Rev. 1.8, 09-Jan-2019 Document Number: 81680 2 For technical questions, contact: EMIFilter vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000