VO3120 www.vishay.com Vishay Semiconductors 2.5 A Output Current IGBT and MOSFET Driver FEATURES 2.5 A minimum peak output current NC 1 8 V 25 kV/s minimum common mode rejection CC (CMR) at V = 1500 V CM A 2 7 V O I = 2.5 mA maximum supply current CC C 3 6 V Under voltage lock-out (UVLO) with hysteresis O Wide operating V range: 15 V to 32 V CC NC 4 5 V EE Shield 0.2 s maximum pulse width distortion 20530 1 Industrial temperature range: - 40 C to 110 C V DE 0.5 V maximum low level output voltage (V ) OL 19813 Reinforced insulation rated per DIN EN 60747-5-2 Material categorization: For definitions of compliance DESCRIPTION please see www.vishay.com/doc 99912 The VO3120 consists of a LED optically coupled to an APPLICATIONS integrated circuit with a power output stage. This optocoupler is ideally suited for driving power IGBTs and Isolated IGBT/MOSFET gate driver MOSFETs used in motor control inverter applications. The AC and brushless DC motor drives high operating voltage range of the output stage provides Induction stove top the drive voltages required by gate controlled devices. The voltage and current supplied by this optocoupler makes it Industrial inverters ideally suited for directly driving IGBTs with ratings up to Switch mode power supplies (SMPS) 800 V/50 A. For IGBTs with higher ratings, the VO3120 can Uninterruptible power supplies (UPS) be used to drive a discrete power stage which drives the IGBT gate. AGENCY APPROVALS UL - file no. E52744 system code H, double protection cUL - file no. E52744, equivalent to CSA bulletin 5A DIN EN 60747-5-2 (VDE 0884) and reinforced insulation rating available with option 1 ORDERING INFORMATION DIP-8 V O 31 20 x - X 0 T PART NUMBER PACKAGE OPTION TAPE 7.62 mm AND Option 7 Option 9 REEL > 0.1 mm > 0.7 mm PACKAGE UL, cUL UL, cUL, VDE DIP-8, tubes VO3120 VO3120-X001 SMD-8, option 7, tape and reel VO3120-X007T - SMD-8, option 9, tape and reel - VO3120-X019T Rev. 1.4, 19-Oct-12 Document Number: 81314 1 For technical questions, contact: optocoupleranswers vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 VO3120 www.vishay.com Vishay Semiconductors TRUTH TABLE V - V V - V CC EE CC EE LED POSITIVE GOING NEGATIVE GOING V 0 (TURN ON) (TURN OFF) Off 0 V to 32 V 0 V to 32 V Low On 0 V to 11 V 0 V to 9.5 V Low On 11 V to 13.5 V 9.5 V to 12 V Transition On 13.5 V to 32 V 12 V to 32 V High ABSOLUTE MAXIMUM RATINGS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL VALUE UNIT INPUT Input forward current I 25 mA F Peak transient input current < 1 s pulse width, 300 pps I 1A F(TRAN) Reverse input voltage V 5V R Output power dissipation P 45 mW diss OUTPUT (1) High peak output current I 2.5 A OH(PEAK) (1) Low peak output current I 2.5 A OL(PEAK) Supply voltage (V - V )0 to + 35 V CC EE Output voltage V 0 to + V V O(PEAK) CC Output power dissipation P 250 mW diss OPTOCOUPLER Isolation test voltage t = 1 s V 5300 V ISO RMS (between emitter and detector) Storage temperature range T - 55 to + 125 C S Ambient operating temperature range T - 40 to + 110 C A Total power dissipation P 295 mW tot For 10 s, (2) Lead solder temperature 260 C 1.6 mm below seating plane Notes Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. (1) Maximum pulse width = 10 s, maximum duty cycle = 0.2 %. This value is intended to allow for component tolerances for designs with I peak minimum = 2.5 A. See applications section for additional details on limiting I peak. O OH (2) Refer to reflow profile for soldering conditions for surface mounted devices (SMD). Refer to wave profile for soldering conditions for through hole devices (DIP). RECOMMENDED OPERATING CONDITION PARAMETER SYMBOL MIN. MAX. UNIT Power supply voltage V - V 15 32 V CC EE Input LED current (on) I 716 mA F Input voltage (off) V - 3 0.8 V F(OFF) Operating temperature T - 40 + 110 C amb Rev. 1.4, 19-Oct-12 Document Number: 81314 2 For technical questions, contact: optocoupleranswers vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000