VS-ST110SPbF Series www.vishay.com Vishay Semiconductors Phase Control Thyristors (Stud Version), 110 A FEATURES Center gate International standard case TO-94 (TO-209AC) Compression bonded encapsulation for heavy duty operations such as severe thermal cycling Hermetic glass-metal case with ceramic insulator (Glass-metal seal over 1200 V) TO-94 (TO-209AC) Designed and qualified for industrial level Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 PRIMARY CHARACTERISTICS TYPICAL APPLICATIONS I 110 A T(AV) DC motor controls V /V 400 V, 800 V, 1200 V, 1600 V DRM RRM Controlled DC power supplies V 1.52 V TM AC controllers I 150 mA GT T -40 C to +125 C J Package TO-94 (TO-209AC) Circuit configuration Single SCR MAJOR RATINGS AND CHARACTERISTICS PARAMETER TEST CONDITIONS VALUES UNITS 110 A I T(AV) T 90 C C I 175 T(RMS) 50 Hz 2700 A I TSM 60 Hz 2830 50 Hz 36.4 2 2 I t kA s 60 Hz 33.2 V /V 400 to 1600 V DRM RRM t Typical 100 s q T -40 to +125 C J ELECTRICAL SPECIFICATIONS VOLTAGE RATINGS V /V , MAXIMUM REPETITIVE V , MAXIMUM NON-REPETITIVE I /I MAXIMUM AT DRM RRM RSM DRM RRM VOLTAGE TYPE NUMBER PEAK AND OFF-STATE VOLTAGE PEAK VOLTAGE T = T MAXIMUM J J CODE V V mA 04 400 500 08 800 900 VS-ST110S 20 12 1200 1300 16 1600 1700 Revision: 27-Sep-17 Document Number: 94393 1 For technical questions within your region: DiodesAmericas vishay.com, DiodesAsia vishay.com, DiodesEurope vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000VS-ST110SPbF Series www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL TEST CONDITIONS VALUESUNITS 110 A Maximum average on-state current I 180 conduction, half sine wave T(AV) at case temperature 90 C Maximum RMS on-state current I DC at 85 C case temperature 175 T(RMS) t = 10 ms 2700 No voltage t = 8.3 ms reapplied 2830 A Maximum peak, one-cycle I TSM non-repetitive surge current t = 10 ms 2270 100 % V RRM t = 8.3 ms reapplied 2380 Sinusoidal half wave, initial T = T maximum t = 10 ms 36.4 No voltage J J t = 8.3 ms reapplied 33.2 2 2 2 Maximum I t for fusing I t kA s t = 10 ms 25.8 100 % V RRM t = 8.3 ms reapplied 23.5 2 2 2 Maximum I t for fusing I t t = 0.1 to 10 ms, no voltage reapplied 364 kA s Low level value of threshold voltage V (16.7 % x x I < I < x I ), T = T maximum 0.90 T(TO)1 T(AV) T(AV) J J V High level value of threshold voltage V (I > x I ), T = T maximum 0.92 T(TO)2 T(AV) J J Low level value of on-state slope resistance r (16.7 % x x I < I < x I ), T = T maximum 1.79 t1 T(AV) T(AV) J J m High level value of on-state slope resistance r (I > x I ), T = T maximum 1.81 t2 T(AV) J J Maximum on-state voltage V I = 350 A, T = T maximum, t = 10 ms sine pulse 1.52 V TM pk J J p Maximum holding current I 600 H T = 25 C, anode supply 12 V resistive load mA J Typical latching current I 1000 L SWITCHING PARAMETER SYMBOL TEST CONDITIONS VALUESUNITS Maximum non-repetitive rate of Gate drive 20 V, 20 , t 1 s r dI/dt 500 A/s rise of turned-on current T = T maximum, anode voltage 80 % V J J DRM Gate current 1 A, dI /dt = 1 A/s g Typical delay time t 2.0 d V = 0.67 % V , T = 25 C d DRM J s I = 100 A, T = T maximum, dI/dt = 10 A/s, TM J J Typical turn-off time t 100 q V = 50 V, dV/dt = 20 V/s, gate 0 V 100 , t = 500 s R p BLOCKING PARAMETER SYMBOL TEST CONDITIONS VALUESUNITS Maximum critical rate of rise of dV/dt T = T maximum linear to 80 % rated V 500 V/s J J DRM off-state voltage Maximum peak reverse and I , RRM T = T maximum, rated V /V applied 20 mA J J DRM RRM off-state leakage current I DRM Revision: 27-Sep-17 Document Number: 94393 2 For technical questions within your region: DiodesAmericas vishay.com, DiodesAsia vishay.com, DiodesEurope vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000