VS-ST780CL Series www.vishay.com Vishay Semiconductors Phase Control Thyristors (Hockey PUK Version), 1350 A FEATURES Center amplifying gate Metal case with ceramic insulator International standard case B-PUK (TO-200AC) Designed and qualified for industrial level Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 TYPICAL APPLICATIONS DC motor controls B-PUK (TO-200AC) Controlled DC power supplies PRIMARY CHARACTERISTICS AC controllers I 1350 A T(AV) V /V 400 V, 600 V DRM RRM V 1.31 V TM I 100 mA GT T -40 C to +125 C J Package B-PUK (TO-200AC) Circuit configuration Single SCR MAJOR RATINGS AND CHARACTERISTICS PARAMETER TEST CONDITIONS VALUES UNITS 1350 A I T(AV) T 55 C hs 2700 A I T(RMS) T 25 C hs 50 Hz 24 400 I A TSM 60 Hz 25 600 50 Hz 2986 2 2 I t kA s 60 Hz 2726 V /V 400 to 600 V DRM RRM t Typical 150 s q T -40 to 125 C J ELECTRICAL SPECIFICATIONS VOLTAGE RATINGS V /V , MAXIMUM REPETITIVE V , MAXIMUM I /I MAXIMUM DRM RRM RSM DRM RRM VOLTAGE TYPE NUMBER PEAK AND OFF-STATE VOLTAGE NON-REPETITIVE PEAK VOLTAGE AT T = T MAXIMUM J J CODE V V mA 04 400 500 VS-ST780C..L 80 06 600 700 Revision: 28-Sep-17 Document Number: 94415 1 For technical questions within your region: DiodesAmericas vishay.com, DiodesAsia vishay.com, DiodesEurope vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000VS-ST780CL Series www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL TEST CONDITIONS VALUESUNITS 1350 (500) A Maximum average on-state current 180 conduction, half sine wave I T(AV) at heatsink temperature double side (single side) cooled 55 (85) C Maximum RMS on-state current I DC at 25 C heatsink temperature double side cooled 2700 T(RMS) t = 10 ms 24 400 No voltage reapplied t = 8.3 ms 25 600 A Maximum peak, one-cycle I TSM non-repetitive surge current t = 10 ms 20 550 100 % V RRM reapplied t = 8.3 ms 21 500 Sinusoidal half wave, initial T = T maximum t = 10 ms J J 2986 No voltage reapplied t = 8.3 ms 2726 2 2 2 Maximum I t for fusing I t kA s t = 10 ms 2112 100 % V RRM reapplied t = 8.3 ms 1928 2 2 2 Maximum I t for fusing I t t = 0.1 to 10 ms, no voltage reapplied 29 860 kA s Low level value of threshold voltage V (16.7 % x x I < I < x I ), T = T maximum 0.80 T(TO)1 T(AV) T(AV) J J V High level value of threshold voltage V (I > x I ), T = T maximum 0.90 T(TO)2 T(AV) J J Low level value of on-state slope resistance r (16.7 % x x I < I < x I ), T = T maximum 0.14 t1 T(AV) T(AV) J J m High level value of on-state slope resistance r (I > x I ), T = T maximum 0.13 t2 T(AV) J J Maximum on-state voltage V I = 3600 A, T = T maximum, t = 10 ms sine pulse 1.31 V TM pk J J p Maximum holding current I 600 H T = 25 C, anode supply 12 V resistive load mA J Typical latching current I 1000 L SWITCHING PARAMETER SYMBOL TEST CONDITIONS VALUESUNITS Maximum non-repetitive rate of rise Gate drive 20 V, 20 , t 1 s r dI/dt 1000 A/s T = T maximum, anode voltage 80 % V of turned-on current J J DRM Gate current 1 A, dI /dt = 1 A/s g Typical delay time t 1.0 d V = 0.67 % V , T = 25 C d DRM J s I = 750 A, T = T maximum, dI/dt = 60 A/s, TM J J Typical turn-off time t 150 q V = 50 V, dV/dt = 20 V/s, gate 0 V 100 , t = 500 s R p BLOCKING PARAMETER SYMBOL TEST CONDITIONS VALUESUNITS Maximum critical rate of rise of dV/dt T = T maximum linear to 80 % rated V 500 V/s J J DRM off-state voltage Maximum peak reverse and I , RRM T = T maximum, rated V /V applied 80 mA J J DRM RRM I off-state leakage current DRM Revision: 28-Sep-17 Document Number: 94415 2 For technical questions within your region: DiodesAmericas vishay.com, DiodesAsia vishay.com, DiodesEurope vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000