MPY20W1150FA00MSSD WIMA

D WIMA MP 3-Y2 Metallized Paper (MP) RFI-Capacitors Class Y2 PCM 10 mm and 15 mm Special Features Electrical Data Particularly high reliability against Capacitance range: Test specifications: active and passive flammability 1000 pF to 0.022 mF (E12-values on request) In accordance with IEC 60384-14 Excellent self-healing as well as Rated voltage: Maximum pulse rise time: high voltage strength 250 VAC Capacitance Pulse rise time V/msec High degree of interference Continuous DC voltage* (general guide): pF/mF max. operation suppression due to good T 1000 V 1000 ... 4700 2500 attenuation and low ESR Capacitance tolerances: 6800 ... 0.022 1750 For temperatures up to +110 C 20% According to RoHS 2011/65/EU Operating temperature range: for pulses equal to a voltage amplitude 40) C to +110) C with 2 x 250 VAC = 355 V Climatic test category: Typical Applications according to IEC 60384-14 40/110/56/C in accordance with IEC Test voltage: 2700 VDC, 2 sec. Insulation resistance at +20+ C: Class Y2 RFI applications to meet Reliability: 3 12 x 10 M EMC regulations Operational life 300 000 hours Measuring voltage: 100 V/1 min. Capacitors connected to the mains Failure rate 1 fit (0.5 x U and 40) C) r Dissipation factors: between phase or neutral and 3 tan d T 13 x 10 at 1 kHz and +20+ C earthed casing Approvals: By-passing of the basic or supplementary insulation, Country Authority Specification Symbol Approval-No. pulse peak voltage T 5 kV V D E Germany VDE IEC 60384-14/3 87455 EN 60384-14 Construction USA/Canada UL UL 60384-14 E 100438 Dielectric: CAN/CSA-E60384-14 Paper, epoxy resin impregnated Capacitor electrodes: Vacuum-deposited Mechanical Tests Packing Internal construction: Pull test on pins: Available taped and reeled. 10 N in direction of pins Capacitor paper according to IEC 60068-2-21 Detailed taping information and graphs Vacuum-deposited electrode Vibration: at the end of the catalogue. Metal contact layer 6 hours at 10 ... 2000 Hz and 0.75 mm (schoopage) displacement amplitude or 10 g in For further details and graphs please Terminating wire accordance with IEC 60068-2-6 refer to Technical Information. Low air density: 1kPa = 10 mbar in accordance with IEC 60068-2-13 Bump test: Encapsulation: 2 Self-extinguishing epoxy resin, UL 94 V-0. 4000 bumps at 390 m/sec in accordance with IEC 60068-2-29 metal foil Terminations: * If safety-approved EMI suppression Tinned wire. capacitors are operated with a DC vol- Marking: tage being above the specified AC voltage Marking: Black on Silver. rating the given approvals are no longer valid (IEC 60384-14). Furthermore the permissible pulse rise time du/dt (F ) will be subject to a reduction max. according to F = F x 2 x UAC / UDC max. r if the DC operating voltage UDC is higher than 2 x UAC 93 11.14 6800 pF -- -- 0.01 F -- 0.015 F PCM15 -- 0.022 F -- 1000 pF -- 1500 pF -- 2200 pF PCM 10 -- 3300 pF -- 4700 pF D WIMA MP 3-Y2 Continuation General Data 250 VAC* Capacitance W H L PCM** Part number 1000 pF 4 8.5 13.5 10 MPY20W1100FA00 1500 4 8.5 13.5 10 MPY20W1150FA00 2200 4 8.5 13.5 10 MPY20W1220FA00 3300 4 8.5 13.5 10 MPY20W1330FA00 4700 5 10 13.5 10 MPY20W1470FB00 6800 5 13 19 15 MPY20W1680FC00 0.01 mF 5 13 19 15 MPY20W2100FC00 0.015 6 14 19 15 MPY20W2150FD00 0.022 7 15 19 15 MPY20W2220FE00 * f = 50/60 Hz Part number completion: ** PCM = Printed circuit module = pin spacing Tolerance: 20 % = M Packing: bulk = S Upon request with long pins 35-2 mm max. Pin length: 6-2 = SD Dims. in mm. Taped version see page 140. 10 W L Z 1 H 7 5 3 6-2 0.1 d = 0.6 P if PCM 10 d PCM 7 5 at the pin exit d = 0.8 P if PCM 15 3 points (0.5) 0.01 1135 730 57100 1000 f/MHz Impedance change with frequency (general guide) Rights reserved to amend design data without prior notification. 94 11.14