A Dimensions: mm B Recommended land pattern: mm D1 Electrical Properties: Properties Test conditions Value Unit Tol. Capacitance 10.2 Vrms, 1 MHz 10% C 220000 pF 20% Rated voltage U 6.3 V (DC) max. R Dissipation factor 10.2 Vrms, 1 MHz 10% DF 10% typ. Isolation Resistance Apply U for 120 s max. R 0.5 G R Iso Precondition for Class II MLCC measurement: Apply a preheat treatment 15010C for 1 hour. The measurement should be applied after 242 hrs the part was stored under ambient conditions. There is not any precondition necessary for Class I MLCC. C Schematic: E General information: General Purpose MLCC Ceramic Type: X5R Class II Temperature Coeffecient: 15% max. Storage Conditions: 35C, <45% RH Operating Temperature: -55 C bis +85 C Dielectric Strength: 5 sec. 250% U Charge & Discharge Current < 50mA R General Test conditions: 25C, 30-70% RH if not specified differently FIT according to separate documentation DESCRIPTION L 0.05 1.0 W 0.05 0.5 WCAP-CSGP Ceramic Capacitors H 0.05 0.5 Wrth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions E +0.05/-0.10 0.25 Max-Eyth-Str. 1 74638 Waldenburg Order.- No. l 1.50 SIZE Germany p 0.50 Tel. +49 (0) 79 42 945 - 0 www.we-online.com 885012105002 A4 1.0 2014-11-10 SSt PSL w 0.50 eiSos we-online.com REV DATE BY CHECKED Size: 0402 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Wrth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Wrth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.D2 Mechanical Properties: Properties Definition Adhesive Strength of Termination 0402 & 0603 10 1 sec 5N > 0603 10 1 sec 10N all 3 directions, 2 hours each 10 - 55 - 10 Hz, Vibration Resistance amplitude 0.75 mm or 10 g Resistance to Solder Heat Solder Temperature 260C 5C Dipping Time 10 1 sec Specific Refer to Soldering Profile DESCRIPTION WCAP-CSGP Ceramic Capacitors Wrth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Order.- No. SIZE Germany Tel. +49 (0) 79 42 945 - 0 www.we-online.com 885012105002 A4 1.0 2014-11-10 SSt PSL eiSos we-online.com REV DATE BY CHECKED Size: 0402 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Wrth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Wrth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.