60 Watts xppower.com ECP Series Low Profile Design Compact Size, 4x 2 IT & Medical Approvals Single, Dual and Triple Output <0.5 W No Load Input Power Peak Load Capability 3 Year Warranty Specification Input General Input Voltage 85-264 VAC, derate from 100% load at Efficiency 88% typical at 230 VAC and full load 90 VAC to 90% load at 85 VAC Isolation 4000 VAC Input to Output Input Frequency 47-63 Hz 1500 VAC Input to Ground 500 VDC Output to Ground Input Current 0.85 A max at 115 VAC Switching Frequency 30-130 kHz variable Inrush Current 100 A max at 230 VAC, cold start at 25 C MTBF >400 kHrs to MIL-HDBK-217F Power Factor EN61000-3-2, class A at 25 C, GB No Load Input Power <0.5 W Earth Leakage Current <250 A at 264 VAC, 60 Hz Environmental Input Protection Internal T2 A/250 V fuse in both line and neutral Operating Temperature -20 C to +70 C, derate from 100% load at 50 C to 50% load at 70 C Cooling Natural convection Output Operating Humidity 5% to 95% RH, non condensing Output Voltage See table Operating Altitude 3000 m max Output Voltage Trim 10% on V1 only, output 2 on multi output Storage Temperature -40 C to +85 C models will track by the same percentage Shock 30 g pk, half sine, 6 axes Minimum Load 10% minimum load required on all outputs of multi output models Vibration 2 g rms, 5 Hz to 500 Hz, 3 axes Start Up Delay 1.3 s max EMC & Safety Start Up Rise Time 15 ms typical Hold Up Time 16 ms min at full load at 115 VAC Emissions EN55011/22, level B conducted & level A Total Regulation Output 1: 2% from 0% load to 100% load radiated Output 2: 5% from 20% load to 100% load Harmonic Currents EN61000-3-2, class A Output 3: 5% from 10% load to 100% load Voltage Flicker EN61000-3-3 Remote Sense Fitted to US05 version, compensates for ESD Immunity EN61000-4-2, 4 kV indirect contact, 0.5 V drop Perf Criteria A Transient Response 4% max deviation, recovering to less than Radiated Immunity EN61000-4-3, 3 V/m, Perf Criteria A 1% within 500 s for 50% step load EFT / Burst EN61000-4-4, level 3 Perf Criteria A change at 1 A/s Surge EN61000-4-5, installation class 3, Ripple & Noise 1% pk-pk (2% for US05 version), Perf Criteria A measured with 20 MHz bandwidth Conducted Immunity EN61000-4-6, 3 V Perf Criteria A Overvoltage Protection 115-140% of nominal output voltage Dips & Interruptions EN61000-4-11, 30% 10 ms, 60% 100 ms, on V1 only, recycle input to reset 100% 5000 ms, Perf Criteria A, B, B Overload Protection 120-160% of nominal power EN60601-1-2, 30% 500 ms, 60% 100 ms, Short Circuit Protection Trip and restart (hiccup mode) 100% 10 ms, 100% 5000 ms, Perf Criteria A, A, A, B Temperature 0.02%/C max Coefficient Safety Approvals UL62368-1, IEC62368-1, EN62368-1, ANSI/AAMI ES 60601-1, IEC60601-1, EN60601-1, CE & UKCA meets all applicable directives & legislation. AC-DCAC-DC ECP60 Models and Ratings Output 1 Output 2 Output 3 Output Model Number (1) (1) Power Voltage Current Peak Voltage Current Peak Voltage Current 55 W +5.0 VDC 11.0 A 14.3 A ECP60US05 60 W +5.0 VDC 7.0 A 9.1 A +12.0 VDC 3.0 A 3.90 A ECP60UD01 60 W +5.0 VDC 7.0 A 9.1 A +15.0 VDC 2.0 A 2.60 A ECP60UD02 60 W +5.0 VDC 7.0 A 9.1 A +24.0 VDC 1.5 A 1.95 A ECP60UD03 60 W +5.0 VDC 7.0 A 9.1 A +12.0 VDC 3.0 A 3.90 A -12.0 V 0.30 A ECP60UT01 60 W +5.0 VDC 7.0 A 9.1 A +15.0 VDC 2.0 A 2.60 A -15.0 V 0.30 A ECP60UT02 60 W +5.0 VDC 7.0 A 9.1 A +24.0 VDC 1.5 A 1.95 A +12.0 V 0.30 A ECP60UT03 60 W +5.0 VDC 7.0 A 9.1 A +24.0 VDC 1.5 A 1.95 A -12.0 V 0.30 A ECP60UT04 Notes 1. Peak load lasting <30 s with a maximum duty cycle of 10%, average output power not to exceed nominal. Mechanical Details CN1 - Input Connector 4.00 (101.6) Pin 1 Neutral Pin 2 Not Fitted 3.75 (95.2) Pin 3 Line Voltage Adj. Mates with JST housing VHR-3N and JST Series 1 SVH-21T-P1.1 crimp terminals CN3 1 6 Mounting holes marked with CN2 must be connected to safety earth 2.00 (50.8) CN2 6 CN2 Output Connector 1.75 1.75 3 (44.4) 1 (44.4) UD/UT US05 CN1 1 Pin 1 V2 +5V Pin 2 V1 +5V Pin 3 V1 +5V UD/UT US05 Pin 4 RTN RTN 0.13 0.01 (3.4 0.3) Pin 5 RTN RTN Mounting hole need to be isolated from ground Pin 6 V3 RTN Mates with JST housing VHR-6N and JST Series SVH-21T-P1.1 crimp terminals 1.04 1.20 (26.3) (30.4) CN3 Sense Connector Pin 1 -Sense Pin 2 +Sense Fitted to ECP60US05 only. Mates 0.06 (1.6) 0.1 (2.5) with Molex Housing 22-01-1022 and 2759 crimp terminals Notes 1. All dimensions are in inches (mm). 3. Tolerance: 0.02 (0.5) unless stated 2. Weight: 0.34 lbs (155 g) approx. Derating Curve 100 80 60 40 20 0 -20 -10 0 10 20 30 40 50 60 70 80 Ambient Temperature (C) 01 Sept 2021 Output Power (%)