800 Watts xppower.com HDS800 Series High Efficiency up to 92% 1U Profile, High Power Density Programmable Output Voltage (0-105%) Programmable Output Current (0-105%) Parallel Operation Fully Featured Signals & Controls 3 Year Warranty Specification Input General Input Voltage 90-264 VAC (127-370 VDC), Efficiency See model table see derating curve Isolation 3000 VAC Input to Output, Input Frequency 47-63 Hz 1500 VAC Input to Ground, Input Current 9.3 A/3.7 A typical at 100/240 VAC 500 VAC Output to Ground Switching Frequency PFC 65 kHz typical, PWM 40-200 kHz Inrush Current 30.0 A/60.0 A typical at 115/230 VAC variable Power Factor 0.98/0.95, typical at 115/230 VAC full load 3 Power Density 10.1 W/in Earth Leakage Current <1.0 mA at 264 VAC/60 Hz Signals & Controls Enable, Current Share, V Program, Input Protection T or F15 A/250 V internal fuse I Program, 5 V Standby, PWM switching MTBF 90 kHrs to MIL-HDBK-217F at 25 C Output Output Voltage See model table Environmental Output Trim 5.0% by potentionmeter Operating Temperature -20 C to 70 C, derate linearly from 100% Output Voltage Program 0-105% of rated output load at 50 C to 50% load at 70 C Output Current Program 0-105% of rated output Cooling Internal fan fitted. Speed increases with load Initial Set Accuracy 1% and internal temperature Minimum Load No minimum load required Operating Humidity 20-90% R.H. non-condensing Start Up Delay 800 ms maximum Storage Temperature -40 C to +85 C Start Up Rise Time 100 ms maximum at full load Storage Humidity 10-95% R.H. Hold Up Time 8 ms minimum Vibration 10-500 Hz, 2g 10 min/cycle, 60 min Line Regulation 1% period for each axis. Compliant to IEC68-2-6, IEC 68-2-64 Load Regulation V1: 1%, standby output: 3% Transient Response <1% for a 25% step load change EMC & Safety Ripple & Noise 150 mV pk-pk all voltages, see note 1 Overvoltage Protection Tracks output voltage. See application Emissions EN55032 class A conducted & radiated notes, Recycle AC to reset Harmonic Currents EN61000-3-2 class A Overtemperature Primary and secondary heatsinks monitored. Voltage Flicker EN61000-3-3 Protection Output shuts down, auto recovers ESD Immunity EN61000-4-2, 4 kV contact, Overload Protection >105% rated power, constant current 8 kV air discharge, Perf Criteria A Radiated Immunity EN61000-4-3, 3 V/m, Perf Criteria A Short Circuit Protection Auto recovery EFT/Burst EN61000-4-4, level 2, Perf Criteria A Temperature 0.02%/C (0-50 C) Coefficient Surge EN61000-4-5, installation class 3, Perf Criteria A Remote Sense Compensates for 0.5 V max voltage drop Conducted Immunity EN61000-4-6, 3 V, Perf Criteria A If remote sense is not required, local sense must be used Magnetic Field EN61000-4-8, 1 A/m, Perf Criteria A Enable Output must be enabled. See application Dips & Interruptions EN55024 , >95% 1 0 ms, 30% 500 ms, notes, power supply is shipped with enable >95% 5000 ms, Perf Criteria A, A, B links fitted Safety Approvals UL62368-1, CSA C22.2 No 62368-1-14, EN 62368-1, IEC62368-1:2014, Current Share 5 supplies can share within 5% CE (Meets all applicable directives), UKCA Standby Output 5 V at 0.5 A, present whenever AC is applied (Meets all applicable legislation) (9V at 0.3A, user selectable, by connecting VSET, Pin 8 of CN2 to GND) AC-DCAC-DC HDS800 Models and Ratings Output Current (2) Output Power Output Voltage V1 Efficiency Model Number Min Max 800 W 12.0 VDC 0.0 A 66.7 A 89% HDS800PS12 800 W 15.0 VDC 0.0 A 53.4 A 90% HDS800PS15 800 W 24.0 VDC 0.0 A 33.5 A 92% HDS800PS24 800 W 30.0 VDC 0.0 A 26.7 A 92% HDS800PS30 800 W 36.0 VDC 0.0 A 22.3 A 92% HDS800PS36 800 W 48.0 VDC 0.0 A 16.7 A 92% HDS800PS48 800 W 60.0 VDC 0.0 A 13.4 A 92% HDS800PS60 Notes 1. Ripple & noise is measured with 20 MHz bandwidth and using 12twisted pair-wire terminated with 0.1 F & 47 F capacitors in parallel. 2. Measured with 230 VAC input and full load. Mechanical Details 1 2 1.61 (40.9) 1 2 1 2 9.80 (249.0) 1 2 +V M6 -V 3 x M4 (bottom side) Penetration Depth = 4mm TRIM CN2 STATUS 2.91 Max Torque = 1.27 Nm LED (74.0) 5.00 Airflow (127.0) E 2.52 N (64.0) L 0.55 (14.0) 7.80 (198.0) 1.46 (37.0) 1.06 (26.9) 0.81 (20.5) 6 x M4 (Both sides) 0.98 (25.0) Penetration Depth = 4mm Max Torque = 1.27 Nm 0.45 (11.5) 8.70 (221.0) 0.32 (8.0) CN2 Control Pin Connections Pin Functio Description Pin Function Description Pin Function Description +5V/0.5 A or +9V/0.3 Mating connector CN2: Manufacturer :JST Housing: 1 VS+ Remote sense (+) 9 EN- Inhibit On/Off(-) 17 AUX A Standby power PHDR-24VS Positive Output Contacts: SPHD-002T-P0.5 2 VO+ 10 GND Ground 18 GND Ground Voltage (28-24 AWG) 2 3 VS- Remote Sense (-) 11 EN+ Inhibit On/Off (+) 19 SCL I C Serial Clock Negative Output +5V/0.5 A or +9V/0.3 2 Notes 4 VO- 12 AUX 20 SDA I C Serial Data Voltage A Standby power 1. All dimensions are in inches (mm). +5V/0.5 A or 5 POK Power OK 13 ACI I Program 21 AUX 2. Weight 3.85 lb (1.75 kg) +9V/0.3 A power 3. Maintain 2 (50mm) clear space at each end. 6 GND Ground 14 GND Ground 22 GND Ground *Only usable with driver board KIT-RS232-X Parallel Operation 7 PAR 15 VCI V Program 23 RX* Receive or KIT-RS485-1 Current Share 8 VSET Aux Output Setting 16 GND Ground 24 TX* Transmit Derating Curve Thermal Derating Curve Input Derating Curve 100 100 80 90 60 80 70 40 60 20 50 40 -10 0 10 20 304050 60 70 Ambient Temperature (C) 90 100 110 120 264 Input Voltage (VAC) Load (%) 24 2 23 1 Load (%)