Leaded ResistoRs High Power Type Wirewound Resistors Ultra Miniature Style PNP Series Feat URes Power Rating 1W, 2W, 3W, 4W Resistance Tolerance 1%, 5% T.C.R. 300ppm/C Flameproof Multi-layer Coating Meets UL-94V-0 Flameproof Feature Meets Overload Test UL-1412 iNt Rod UCtio N de Rati NG CURVe The resistor element is a resistive wire which is For resistors operated in ambient temperatures above 70C, power rating must be derated wound in a single layer on a ceramic rod, with in accordance with the curve below. tinned connecting wires of electrolytic copper 70 200 275 C welded to the end-caps. The ends of the Rated Load (%) 100 resistive wire and the leads are connected to 80 the caps by welding. The resistors are coated 60 with layers of green color flame-proof lacquer. 40 High power in small packages. 20 Ambient Temperature (C) 50 100 150 200 250 300 di MeNsio Ns Unit: mm st YLe di MeNsio N Ultra Miniature L d H d d PNP100 6.30.5 2.40.2 282.0 0.550.05 H L D PNP200 9.00.5 3.30.3 262.0 0.550.05 PNP300 11.51.0 4.50.5 352.0 0.80.05 th color code: violet PNP400 15.51.0 5.00.5 332.0 0.80.0561 Note: High Power Type Ultra Miniature Style PNP Series eLeCt RiCa L CHa Ra Cte Risti Cs st YLe PNP100 PNP200 PNP300 PNP400 Power Rating at 70C 1W 2W 3W 4W Dielectric Withstanding Voltage 300V Resistance Range (1%) 0.22 - 130 0.1 - 820 0.1 - 2.2K 0.1 - 2.8K Resistance Range (5%) 0.1 - 130 0.068 - 820 0.025 - 2.2K 0.03 - 2.8K Operating Temp. Range -40C to +200C Temperature Coefficient 300ppm/C Note: Special value is available on request eNViRo NMeNta L CHa Ra Cte Risti Cs PeRFo RMa NCe test test M et Hod a PPRaise Short Time Overload IEC 60115-1 4.13 10 times rated power for 5 Sec. 2.0%+0.05 Voltage Proof IEC 60115-1 4.7 in V-block for 60 Sec., test voltage by type By type Temperature Coefficient IEC 60115-1 4.8 -55C to +155C By type Insulation Resistance IEC 60115-1 4.6 in V-block for 60 Sec. >100M Solderability IEC 60115-1 4.17 2355C for 30.5 Sec. 95% Min. coverage No deterioration of Solvent Resistance of Marking IEC 60115-1 4.30 IPA for 50.5 Min. with ultrasonic coatings and markings Robustness of Terminations IEC 60115-1 4.16 Direct load for 10 Sec. in the direction of the terminal leads 2.5kg (24.5N) Damp Heat Steady State IEC 60115-1 4.24 402C, 90-95% RH for 56 days, loaded with 0.1 times RCWV 5.0%+0.05 Endurance at 70C IEC 60115-1 4.25 702C at RCWV for 1,000 Hr. (1.5 Hr. on, 0.5 Hr. off) 5.0%+0.05 Temperature Cycling IEC 60115-1 4.19 -55C Room Temp. +155C Room Temp. (5 cycles) 1.0%+0.05 Resistance to Soldering Heat IEC 60115-1 4.18 2603C for 101 Sec., immersed to a point 30.5mm from the body 1.0%+0.05 No evidence of flaming Accidental Overload Test IEC 60115-1 4.26 4 times RCWV for 1 Min. or arcing Note: Rated Continuous Working Voltage (RCWV) = Power Rating x Resistance Value