LIGHTING DIMMER DIM-20 INSTRUCTION MANUAL ZAMEL Sp. z o.o. ul. Zielona 27, 43-200 Pszczyna, Poland Tel. +48 (32) 210 46 65, Fax +48 (32) 210 80 04 www.zamelcet.com, e-mail: marketing zamel.pl DESCRIPTION TECHNICAL PARAMETERS DIM-20 The device DIM-20 is used to control the lighting level of chosen light sources Input (supply) terminals: L, N described in Load capacity table. Sin- Input rated voltage: 230 V AC gle or double monostable light push- Input voltage tolerance: -15 +10 % buttons are responsible for the control. Nominal frequency: 50 Hz The buttons connected in a parallel way Rated power consumption: 10 mA enable lighting operating from different Supply voltage control indicator: LED green places. The device has the function of switching on/off and of smooth brighte- Release terminals: IN, IN, IN ning/dimming the light. DIM-20 enables single monostable light push-button Lighting control: intelligent lighting system control and gi- double monostable light push-button ves comfort and economy in use. Output (load) terminals: N, Output switch on indicator: LED red Output (load) power: 30 500 W Control element: MOS transistor FEATURES Numer of terminal clamps: 11 2 Section of connecting cables: 0,2 2,50 mm Intelligent lighting control, o bulb light brightness level control, Ambitne temperature range: -20 +45 C halogen light brightness level control Operating position: free supplied by means of toroidal or elec- Mounting: rail TH35 (EN 60715) tronic transformer, Protection degree: IP20 (EN 60529) energy-saving fluorescent lamp (com - Protective class: II pact) light brightness level control, used to cooperate with a dimmer, Overvoltage category: II energy saving in stand-by position, Pollution degree: 2 cooperation with control push-buttons Rated impulse withstand voltage: 2 kV (EN 60669-2-1), 1 kV (EN 61000-4-5) equipped with neon light, Dimensions (height / width / depth): double-module (35 mm) 90x35x66 mm maximum power load 500 W, Weight: 0,135 kg input rated voltage indicator, output (load) switch on indicator, Reference standards: EN 60669-1 EN 60669-2-1 EN 61000-4-2,3,4,5,6,11 double-module casing, TH 35 DIN rail installation. APPEARANCE The device is designed for Input (supply) terminal (L) Release system terminals single-phase installation and must be installed in accor- ( , , IN) dance with standards valid Input (supply) terminal (N) in a particular country. The device should be connected CAUTION according to the details inc- luded in this operating manual. Installation, connection and control should be carried out by a qualified electrician staff, who act Supply voltage Output (load) switch on in accordance with the service manual and indicator indicator the device functions. Disassembling of the device is equal with a loss of guarantee and can cause electric shock. Before installa- tion make sure the connection cables are not under voltage. The cruciform head screwdriver 3,5 mm should be used to instal the device. Improper transport, storage, and use of the device influence its wrong functioning. It is not advisable to instal the device in the following cases: if any device part is missing or the device is damaged or deformed. In case of improper functioning of the device contact the producer. The symbol means selective collecting of electrical and electronic equipment. It is forbidden to put the Input (supply) terminals used equipment together with other (N, N, N, , , ) waste. VER. 002 02.04.2012MOUNTING, FUNCTIONING CONNECTING TIME COURSES 1. Disconnect the power supply from the ma- Level ins by the phase fuse, the circuit-breaker or memory the switch-disconnector that are joined to the proper circuit. 2. Check if there is no voltage on connection cables by means of a special measure equ- ipment. 3. Install DIM-20 device in the switchboard on TH-35 DIN rail. 4. Connect the cables with the terminals ac- cording to installing diagram. 5. Switch on the power supply from the ma- ins. The device is used to control the lighting with a total power that does not exceed 500 W. Monostable light push-buttons are re- Level sponsible for the control. The buttons can be memory connected in a parallel way to enable lighting operating from different places. Short pressing and releasing the button (for about <0,8 sec.) tylko w gr causes the light switches on or off. Holding the button for a longer time (>0,8 sec.) causes tylko smooth light dimming or brightening. DIM-20 w d has the function to memorize the preset light brightness level. To memorize the brightness level, press the control push-button (control input IN or ) and DIMENSIONS INNER DIAGRAM hold it for a longer time to obtain the deman- ded brightness level. To memorize the lowest brightness level, again push the button (control input IN or ) and hold it for a longer time to obtain a new demanded brightness level. The adjusted brightness level is remembered in the inner memory of the device and will ope- rate with the next switching on / off the light. Even in case of power supply failure the adjusted brightness level is remembered. TyPICAL APPLICATION RELAy CAPACITy 500 W 300 W 500 W 500 W Digital time programmer PRODUCT FAMILy DIM-20 light dimmer belongs to Dlx light dimmers Device type: 01 serial, basic 02 serial, with memory 10 basic, modular 20 modular with memory, only for DIM-20 device Casing type: M modular P flush junction box Device symbol WARRANTy CARD There is 24 months guarantee on the product 1. ZAMEL provides a two-year warranty for its products. 2. The ZAMEL warranty does not cover: a) mechanical defects resulting from transport, loading / unloading or other circumstances b) defects resulting from incorrect installation or operation of ZAMEL products c) defects resulting from any changes made by CUS- TOMERS or third parties, to products sold or equipment necessary for the correct operation of products sold d) defects resulting from force majeure or other aleatory events for which ZAMEL is not liable e) power supply (batteries) to be equipped with a device in the moment of sale (if they appear) 3. All complaints in relation to the warranty must be provided by the CUSTOMER in writing to the retailer after discovering a defect. 4. ZAMEL will review complaints in accordance with existing regulations. 5. The way a complaint is settled, e.g. replacement of the product, repair or refund, is left to the discretion of ZAMEL. 6. Guarantee does not exclude, does not limit, nor does it suspend the rights of the PURCHASER resulting from the discrepancy between the goods and the contract. Salesman stamp and signature, date of sale VER. 002 02.04.2012