INSTRUCTION INSTALLATION CHANGEOVER SWITCH PIM-03 MANUAL Zakad Mechaniki i Elektroniki ZAMEL sp.j. J.W. Dzida, K. odziska ul. Zielona 27, 43-200 Pszczyna, Poland Tel. +48 (32) 210 46 65, Fax +48 (32) 210 80 04 www.zamelcet.com, e-mail: marketing zamel.pl DESCRIPTION TECHNICAL PARAMETERS PIM-03 installation changeover PIM-03 switch is used in control systems. Input terminals: IN, IN (internal connected) The device equipped with three- Output terminals: 1, 2 position changeover switch I-0-II Number of changeover switch positions: 3 (I, 0, II) enables to choose either the control of one of two output circuits or their Maximum working voltage: 250 V AC total switch off. It also enables coop- Maximum current allowable: 10 A AC 21 eration and control of home building Contact resistance: < 100 m (for 12 V AC) automation devices and receivers Number of terminal clamps: 4 with maximum 10 A current. 2 Section of connecting cables: 0,2 2,50 mm o Ambient temperature range: -20 +45 C Operating position: freely FEATURES Casing mounting: rail TH 35 (acc to PN-EN 60715) Casing protection degree: IP20 (PN-EN 60529) Used in control systems, Protection level: II possible control of home building Overvoltage category: II automation devices, possible direct control of rece- Pollution degree: 2 ivers, Dimensions: mono modular 90x17,5x66 mm middle/central position switch, Weight: 68 g 10 A current capacity, Reference standard: PN-EN 60669-1 PN-EN 60669-2-1 mono modular casing, PN-EN 61000-4-2,3,4,5,6,11 TH35 rail installation. APPEARANCE The device is designed for single-phase installa- tion and must be installed in accordance with stan- dards valid in a particu- Output terminal 1 Output terminal 2 lar country. The device CAUTION should be connected according to the details included in this operating manual. Installation, connec- tion and control should be carried out by a qualified electrician staff, who act in accordance with the service manual and the device functions. Disassembling of the device is equal with a loss of guaran- tee and can cause electric shock. Before Switch installation make sure the connection ca- bles are not under voltage. The cruciform head screwdriver 3,5 mm should be used to instal the device. Improper transport, storage, and use of the device influence its wrong functioning. It is not advisable to instal the device in the following cases: if any device part is missing or the device is damaged or deformed. In case of im- proper functioning of the device contact the producer. Input terminals: IN, IN The symbol means selective collecting of electrical and electronic equipment. It is forbidden to put the used equipment together with other waste. VER. 001 12.02.2010MOUNTING, FUNCTIONING CONNECTING 1. Disconnect power supply by the phase fuse, the circuit-breaker or the switchdisconnector com- bined to the proper circuit. 2. Check if there is no voltage on connection cables by me- CIRCUIT 1 CIRCUIT 2 ans of a special measure equ- ipment. 3. Install the PIM-03 on the TH-35 DIN rail in the switchboard. 4. Connect the cables with the ter- minals in accordance with the installing diagram. L N 5. Switch on the power supply from the mains. The device is ready to work after APPLICATION correct mounting and connecting. If the changeover switch is switched into position I it wil cause short L circuit of contact IN-1, and when N it is switched into position II there is a short circuit of contact IN-2. The changeover switch in position 0 causes output terminals 1 and 2 are insulated from input terminal IN. This device can directly control re- ceivers with power consumption up till 10 A or it cooperates with other home building automation devices. PRODUCT FAMILY The PIM-03 device belongs to PIM product group. INNER DIAGRAM DIMENSIONS Device type: 03 - three-position changeover switch Device symbol WARRANTY CARD There is 24 months guarantee on the product 1. ZMIE ZAMEL SP. J. assures 24 months guarantee for the product. 2. The manufacturers guarantee does not cover any of the following actions: a) mechanical damage during transport, loading / unloading or under other circumstances, b) damage caused by incorrect product mounting or misuse, c) damage caused by unauthorised modifications made by the PURCHASER or any third parties to the product or any other devices needed for the product functioning, d) damage caused by Act of God or any other incidents independent of the manufacturer. 3. The PURCHASER shall lay any claims in writing to the dealer or ZMIE ZAMEL SP. J. 4. ZMIE ZAMEL SP. J. is liable for processing any claim according to current Polish legislation. 5. ZMIE ZAMEL SP. J. shall process the claim at its own discretion: product repair, replacement or money return. 6. The manufacturers guarantee is valid in the Republic of Poland. 7. The PURCHASERs statutory rights in any applicable legislation whether against the retailer arising from the purchase contract or otherwise are not affected by this warranty. Salesman stamp and signature, date of sale VER. 001 12.02.2010