Dual, Low Noise, Wideband Variable Gain Amplifiers AD600/AD602 FEATURES FUNCTIONAL BLOCK DIAGRAM GAT1 2 channels with independent gain control Linear in dB gain response PRECISION PASSIVE SCALING GATING INPUT ATTENUATOR 2 gain ranges REFERENCE INTERFACE AD600: 0 dB to 40 dB C1HI V G A1OP AD602: 10 dB to +30 dB C1LO Accurate absolute gain: 0.3 dB A1CM GAIN CONTROL Low input noise: 1.4 nV/Hz INTERFACE RF2 2.24k (AD600) Low distortion: 60 dBc THD at 1 V output 0dB 12.04dB 22.08dB 36.12dB 694 (AD602) High bandwidth: dc to 35 MHz (3 dB) 6.02dB 18.06dB 30.1dB 42.14dB RF1 20 Stable group delay: 2 ns A1HI FIXED-GAIN Low power: 125 mW (maximum) per amplifier AMPLIFIER A1LO 500 62.5 41.07dB (AD600) R-2R LADDER NETWORK Signal gating function for each amplifier 31.07dB (AD602) Drive high speed ADCs Figure 1. Functional Block Diagram of a Single Channel of the AD600/AD602 MIL-STD-883-compliant and DESC versions available The gain-control interfaces are fully differential, providing an APPLICATIONS input resistance of ~15 M and a scale factor of 32 dB/V (that Ultrasound and sonar time-gain controls is, 31.25 mV/dB) defined by an internal voltage reference. The High performance audio and RF AGC systems response time of this interface is less than 1 s. Each channel Signal measurement also has an independent gating facility that optionally blocks signal transmission and sets the dc output level to within a few GENERAL DESCRIPTION millivolts of the output ground. The gating control input is 1 The AD600/AD602 dual-channel, low noise, variable gain TTL- and CMOS-compatible. amplifiers are optimized for use in ultrasound imaging systems The maximum gain of the AD600 is 41.07 dB, and the maximum but are applicable to any application requiring precise gain, low gain of the AD602 is 31.07 dB the 3 dB bandwidth of both noise and distortion, and wide bandwidth. Each independent models is nominally 35 MHz, essentially independent of the channel provides a gain of 0 dB to +40 dB in the AD600 and gain. The SNR for a 1 V rms output and a 1 MHz noise 10 dB to +30 dB in the AD602. The lower gain of the AD602 bandwidth is typically 76 dB for the AD600 and 86 dB for the results in an improved signal-to-noise ratio (SNR) at the output. AD602. The amplitude response is flat within 0.5 dB from However, both products have the same 1.4 nV/Hz input noise 100 kHz to 10 MHz over this frequency range, the group delay spectral density. The decibel gain is directly proportional to the varies by less than 2 ns at all gain settings. control voltage, accurately calibrated, and supply and temper- ature stable. Each amplifier channel can drive 100 load impedances with low distortion. For example, the peak specified output is 2.5 V To achieve the difficult performance objectives, a proprietary minimum into a 500 load or 1 V into a 100 load. For a circuit form, the X-AMP, was developed. Each channel of the 200 load in shunt with 5 pF, the total harmonic distortion for X-AMP comprises a variable attenuator of 0 dB to 42.14 dB a 1 V sinusoidal output at 10 MHz is typically 60 dBc. followed by a high speed fixed gain amplifier. In this way, the amplifier never has to cope with large inputs and can benefit The AD600J/AD602J are specified for operation from 0C to 70C from the use of negative feedback to precisely define the gain and are available in 16-lead PDIP (N) and 16-lead SOIC packages. and dynamics. The attenuator is realized as a 7-stage R-2R The AD600A/AD602A are specified for operation from 40C to ladder network having an input resistance of 100 , laser +85C and are available in 16-lead CERDIP (Q) and 16-lead SOIC trimmed to 2%. The attenuation between tap points is 6.02 dB packages. The AD600S/AD602S are specified for operation from the gain-control circuit provides continuous interpolation between 55C to +125C, are available in a 16-lead CERDIP (Q) package, these taps. The resulting control function is linear in dB. and are MIL-STD-883-compliant. The AD600S/AD602S are also available under DESC SMD 5962-94572. 1 Patented. Rev. F Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. rights of third parties that may result from its use. Specifications subject to change without notice. No Tel: 781.329.4700 www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Fax: 781.461.3113 2008 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. 00538-001IMPORTANT LINKS for the AD600 602* Last content update 09/11/2013 01:28 pm PARAMETRIC SELECTION TABLES DESIGN COLLABORATION COMMUNITY Variable Gain Amplifier Selection Table Collaborate Online with the ADI support team and other designers about select ADI products. DOCUMENTATION Follow us on Twitter: www.twitter.com/ADI News Design and Operation of Automatic Gain Control Loops for Receivers Like us on Facebook: www.facebook.com/AnalogDevicesInc in Modern Communication Systems X-amp, A New 45-dB, 500-MHz Variable-Gain Amplifier (VGA) Simplifies Adaptive Receiver Designs Choosing High-Speed Signal Processing Components for Ultrasound Systems DESIGN SUPPORT ADI Warns Against Misuse of COTS Integrated Circuits Submit your support request here: Linear and Data Converters Space Qualified Parts List Embedded Processing and DSP Leading Inside Advertorials: Solving Dynamic Range Problems in Analog Systems Telephone our Customer Interaction Centers toll free: Americas: 1-800-262-5643 FOR THE AD600 Europe: 00800-266-822-82 China: 4006-100-006 AD600: Military Data Sheet India: 1800-419-0108 Ultrasound System Considerations and their Impact on Front-End Russia: 8-800-555-45-90 Components Quality and Reliability FOR THE AD602 Lead(Pb)-Free Data AD602: Military Data Sheet SAMPLE & BUY DESIGN TOOLS, MODELS, DRIVERS & SOFTWARE AD600 AD600 SPICE Macro-Model AD602 AD600J SPICE Macro-Model View Price & Packaging AD602 SPICE Macro-Model Request Evaluation Board AD602J SPICE Macro-Model Request Samples Check Inventory & Purchase Find Local Distributors EVALUATION KITS & SYMBOLS & FOOTPRINTS Symbols and Footprints for the AD600 Symbols and Footprints for the AD602 * This page was dynamically generated by Analog Devices, Inc. and inserted into this data sheet. Note: Dynamic changes to the content on this page (labeled Important Links ) does not constitute a change to the revision number of the product data sheet. This content may be frequently modified. Powered by TCPDF (www.tcpdf.org)