Click here for production status of specific part numbers. Evaluates: MAX14813 MAX14813 Evaluation Kit General Description Benefits and Features The MAX14813 evaluation kit (EV kit) provides a proven Easy Evaluation of the MAX14813 design to evaluate the MAX14813 high-voltage, high- Configurable for Three-Level or Five-Level Mode frequency, three-level octal/five-level quad pulser. It also Programmable Master Clock Frequency and Trigger provides the capability to control the MAX14813 through an onboard USB-to-SPI interface, on-board high-frequency Option for External Clock and External Trigger clock generator and synchronous trigger. The EV kit Includes 3.5mm Scope-Probe Jacks for High-Voltage includes a graphical user interface (GUI) for exercising Outputs the beam forming features of the IC, making it a complete Windows XP , Windows 7, Windows 8.1, Windows PC-based evaluation system. 10-Compatible Software EV Kit Contents Fully Assembled and Tested MAX14813EVKIT including the MAX14813EWX+ Proven PCB Layout USB Cable Type A Male to Type B Male RoHS Compliant Ordering Information appears at end of data sheet. MAX14318 EV Kit Photo Windows and Windows XP are registered trademarks and registered service marks of Microsoft Corporation. 19-8669 Rev 0 10/16Evaluates: MAX14813 MAX14813 Evaluation Kit System Block Diagram JUMPERS TO VIO/GND LOW PASS MODE2/ FILTERS MODE1 SYNC/INT 1K 100 INNx, INPx CC1 HVOUT 4:1 (EXCEPT INN5, INP4, INP5) CC0 H1/H2 8 5L JUMPERS 8 TEST INN5/CS DUMMY 1-5, 2-6, 3-7, 4-8 POINTS DIRECT MODE U1 LOADS DIGITAL OR MAX14813 CONTROL INP5/SCLK BEAM FORMING SIGNALS HVOUT 8:5 MODE CONFIGURATION INNx, INPx CC0/SDIO 20K BY JUMPERS AND R PULL-DOWN DIRECT MODE 0 RESISTORS CC1/SDO LVOUT 8:1 8 TEST POINTS INP4 INP4/TRIG MAX14813 SPI THP PC GUI USB TO SPI SMA TRIG CLK EXT FT2232H TXCLK CLKOUT6 -Wire/SPI 160MHZ/80MHZ/40MHZ/20MHZ LVCMOS TRIG CLKOUT12 CRYSTAL CLKIN0 160MHZ 2.5KHZ/5KHZ/10KHZ/CWD MODE OSCILLATOR CLOCK/TRIGGER TRIG EXT 160MHZ GENERATOR CLKIN1 CLKOUT0 SMA LMK01801 20MHz CLKIN1* CLKOUT0* -5V DC, 0.5A power supply (optional if the on-board MAX14318 EV Kit Files LDO is used) FILE DESCRIPTION +5V to +100V DC, 30mA (+100V) to 600mA (+5V) MAX14813EVKitSetupV1.0.ZIP Application Program power supply -5V to -100V DC, -30mA (-100V) to -600mA (-5V) Quick Start power supply Required Equipment Optional (for 5 levels configuration) +5V to +100V DC, 30mA (+100V) to 600mA (+5V) power supply MAX14813 EV kit Optional (for 5 levels configuration) -5V to -100V DC, Type A Male to Type B Male USB Cable -30mA (-100V) to -600mA (-5V) power supply Optional custom controller board or pattern gen- erator to drive the INN1-INN8, INP1-INP8 control Digital storage oscilloscope signals (see the MAX14813 IC data sheet for more It is recommended that the engineer read the MAX14813 information) IC data sheet prior to using the EV kit and GUI. +3.3V DC, 100mA power supply (optional if the on- Note: In the following sections, software-related items are board LDO is used) identified by bolding. Text in bold refers to items directly from the EV kit software. Text in bold and underline +5V DC, 1A power supply refers to items from the Windows operating system. Maxim Integrated 2 www.maximintegrated.com