70-841-015 Artesyn Embedded Technologies

POWER LPQ170 Series Data Sheet 175 Watts Total Power: 110 - 175 Watts Input Voltage: 85 - 264 Vac 120 - 300 Vdc of Outputs: Quad Special FeaS Active power factor correction IEC EN61000-3-2 compliance Adjustable outputs on 1, 3 & 4 Remote sense on main output Single wire current sharing Power fail and remote inhibit Built-in EMI filter Low output ripple Overvoltage protection Electrical Specifications Overload protection Input Thermal overload protection Input range 85-264 Vac 120-300 Vdc DC power good Frequency 47-67 Hz 5 V standby output Inrush current 38 A max, cold start 25C Adjustable floating 4th output Efficiency 75% typical at full load Optional cover (-C suffix) EMI filter Meets FCC Class B conducted RoHS compliant CISPR 22 Class B conducted EN55022 Class B conducted SaF VDE 0878 PT3 Class B conducted UL UL60950 Power factor 0.99 typical CB Certificate and report Safety ground leakage current 1.0 mA 50/60 Hz, 264 Vac input CSA CSA 22.2-234 Level 3 Output CE Mark (LVD) Maximum power 110 W convection (75 W with cover) NEMKO EN 60950/EMKO-TUE 85 W convection - LPQ173 175 W with 30 CFM forced air (130 W with cover - LPQ172) Adjustment range 3.3 - 5.5V on main -12 - 15V on 3rd output 3.3 - 25 V on 4th output - LPQ172 3.3 - 5.5 V on 4th output - LPQ173 Hold-up time 20 ms 175 W load at nominal line Overload protection Short circuit protection on all outputs. Case overload protected 110-145% above peak rating Overvoltage protection Tracks outputs 1, 3 & 4 15 to 35% Standby output 5 V 200 mA regulated 5% ety tureLPQ170 Series Data Sheet Logic Control AC power failure TTL logic signal goes high 100 - 500 msec after V1 output It goes low at least 4 msec before loss of regulation Remote sense Compensates for 0.5 V lead drop min. Will operate without remote sense connected. Reverse connection protected. DC - OK TTL logic signal goes high after main output is in regulation. It goes low when there is a loss of regulation. Environmental Specifications Operating temperature 0 C to 50 C ambient. Derate each output 2.5% per degree from 50 C to 70 C (except for -C version). Storage temperature -40 C to +85 C Temperature coefficient 0.4% per C Electromagnetic susceptibility Designed to meet IE61000-4, -2, -3, -4, -5, -6, -8, -11, Level 3 Humidity Operating non-condensing 5% to 95% Vibration Three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four major resonances 0.75 G peak 5 Hz to 500 Hz, operational MTBF demonstrated >550,000 hours at full load and 25C ambient conditions Ordering Information Maximum Load Maximum Load Model Output Minimum Ripple 1 2 with Convection with 30CFM Peak Load Regulation 3 Number Voltage Load P/P(PARD) Cooling Forced Air LPQ172 5 V (3.3 - 5.5 V) 0 A 15 A 30 A 32 A 2% 50 mV 12 V 0 A 6 A 8 A 10 A 3% 120 mV -12 V (-12 -15 V) 0 A 1.5 A 3 A 3.5 A 3% <1% 3.3-25 V 0.5 A* 2 A 5 A 5.5 A 3% <50mV or 1% LPQ173 5 V (3.3 - 5.5 V) 0 A 10 A 24 A 26 A 2% 50 mV 12 V 0 A 6 A 8 A 10 A 3% 120 mV -12V (-12 -15 V) 0 A .2 A 3 A 3.5 A 3% <1% 5 V (3.3 - 5.5 V) 0 A 10 A 24 A 26 A 2% 50 mV 1. Peak current lasting <30 seconds with a maximum 10% duty cycle. 2. At 25 C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3. Peak-to-peak with 20 MHz bandwidth and 10 F in parallel with a 0.1 F capacitor at rated line voltage and load ranges. 4. 4th output adjustable 3.3 - 25 V factory set at 5 V. 5. *Minimum loads are required when output set below 5 Volts 6. Remote inhibit resets OVP latch 7. LPQ173-C has no convection rating. 8. This product is a Component Power Supply and is only for inclusion by professional installers within other equipment and must not be operated as a standalone product. EMC compliance to appropriate standards must be verified at the system level. This product is for sale to OEMs and System Integrators, including through Distribution Channels. It is not intended for sale to End Users. Note: -C suffix added to the model number indicates cover option and is limited to 50 C operation.