POWER LPS360-M Series Low Power Data Sheet 360 Watt AC-DC Power Supply Total Power: 200 - 360 W Input Voltage: 90 - 264 Vac 120 - 300 Vdc Outputs: Single SPECIAL FEATURES Medical and ITE safeties Active power factor correction 3 x 5 footprint Less than 1U high EN61000-3-2 compliant Remote sense Power fail Electrical Specifications Adjustable main output Input Level B Conducted EMI - Class I Input range: 90 - 264 Vac 120 - 300 Vdc or Class II inputs Frequency: 47 - 63 Hz Overvoltage protection Inrush current: 50 A max., cold start 25 C Overload protection Efficiency: Up to 93% at full load Thermal overload protection EMI/RFI: FCC Class B conducted CISPR22 Class B conducted 12 V fan output EN55022 Class B conducted VDE0878PT3 Class B conducted LPX200 enclosure kit available Power factor: 0.99 typical 5 V Standby output Safety ground leakage 150 uA 132 Vac, 60 Hz for class I, 300 uA 264 Vac, 60 Hz for class II Remote Inhibit current: PMBus commands Output 2 Digital I C interface Maximum power: 200 - 240 W (see de-rating) for convection, 360 W with 400 LFM of forced air Class I and Class II approved Adjustment range: 12 V and 24 V models, -0%, +15%, 15 V and 48 V models, -5%, +10% Dual AC fuses Standby output: 5 V 1A convection, 2 A with forced air Suitable for BF Type applications Fan output: 12 V 0.5 A convection, 1 A forced air Hold-up time: 20ms 240W, 220Vac input 12ms 360 W SAFETY Overload protection: Short circuit protection on all outputs. Case overload protected 110 - 160% TUV 60950, 60601-1 above rating UL 60950, 60601-1 Overvoltage protection: 15 - 50% above nominal output cULus 60950, 60601-1 Logical Control CB Certificate & report Power failure: Open collector logic signal goes high 100 - 500 msec after main output it goes low at least 6 msec before loss of regulation CE Mark (LVD & EMC) Remote sense: Compensates for 0.5 V lead drop min. Will operate without remote sense CCC Approval connected. Reverse connection protected.LPS360-M Series Data Sheet Environmental Specifications Operating temperature: -20 C to 50 C ambient, derate each output as 2.5% per degree from 50 C to 70 C -40 C startup if Standby output 1A (any valid load on main output) -30 C startup if Standby output > 1A (any valid load on main output) Storage temperature: -40 C to +85 C Electromagnetic susceptibility: Designed to meet EN61000-4 -2, -3, -4, -5, -6, -8, -11 Level 3 Humidity: Operating non-condensing 10% to 95% RH Vibration: IEC68-2-6 to the levels of IEC721-3-2 Ordering Information Model Output Minimum Maximum Load with Maximum Load Peak Ripple 2 3 Number Voltage Load Convection Cooling with Forced Air Load Regulation P/P (PARD) LPS363-M 12 V 0 A 20 A 30 A 39 A 2% 120 mV LPS364-M 15 V 0 A 16 A 24 A 31 A 2% 150 mV LPS365-M 24 V 0 A 10 A 15 A 19.5 A 2% 240 mV LPS368-M 48 V 0 A 5 A 7.5 A 9.75 A 2% 480 mV 1. Peak current lasting <3 seconds. 2 . At 25 C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3 . Peak-to-peak with 20 mHz bandwidth and 10 F (tantalum capacitor) in parallel with a 0.1 F capacitor at rated line voltage and load ranges. Pin Assignments Mating Connectors Connector LPS360-M J4 AC Input Molex 09-50-3031 (connector) PINS: 08-52-0072 J4 Pin 1 Neutral J6 AC Ground Molex 01-90020001 Pin 3 Line DC Output Molex 19141-0058/0063 or 19099/0048 Barr Barr-1 Main output + (Barr) Spade lug based on Cable Ampacity/AWG Barr-2 Main output common J5 Control Signals Molex 90142-0010 (USA) PINS: 90119-2110 or J5 Pin 1 +V1 Remote sense Amp: 87977-3 Pin 2 -V1 Remote sense PINS: 87309-8 Pin 3 +5 V Standby J3 Fan Output Molex 51065-0200 Pins: 50212-8100 Pin 4 5 V Standby return The Artesyn Connector Kit 70-841-029, includes all of the above. Pin 5 +Power fail Pin 6** Forced air operation 1. Specifications subject to change without notice. 2. All dimensions in inches (mm), tolerance is 0.02(0.5 mm) Pin 7 Inhibit 3. Mounting holes MH1 and MH2 should be grounded for EMI purposes. Pin 8 GND 4. Mounting hole MH1 is safety ground connection. Pin 9 SDA 5. Specifications are for convection rating at factory settings at 115 VAC input, 25 C unless otherwise stated. Pin 10 SCL 6. This power supply requires mounting on metal standoffs 0.20 (5m) in height. J3 Pin 1 +12 V Fan 7. Warranty: 3 Years Pin 2 12 V fan Return (isolated) 8. Weight: 0.75 lb/0.34 kg ** For forced air operation, connect pin 6 to pin 8 of J5. 2 Digital I C Interface Accessories 2 73-769-001 USB to I C Adapter with USB Cable 2 73-841-030 LPS360-M I C Mating Connector Artesyn Connector Kit 73-769-005 includes both of the above