POWER Intelligent MP Series Data Sheet Up to 1500 Watts Total Power: Up to 1500 W Input Voltage: 85 - 264 VaC 88 - 300 Vdc of Outputs: Up to 24 SPECIAL FEATURES Full medical EN60601 approval 2 Intelligent I C control Voltage adjustment on all outputs 2 (manual or I C) Configurable input and output OK signals and indicators Electrical Specifications Configurable inhibit/enable Input Configurable output UP/DOWN Input range 85 - 264 Vac 88 - 300 Vdc sequencing (limited to 300 Vdc in medical applications) Configurable current limit Frequency 47 - 440 Hz (foldback or constant current) High power density (8.8 W/cu-in) Inrush current 40 A peak maximum (soft start) Intelligent fan (speed control/fault Efficiency Up to 85% full case load status) Power Factor 0.99 typ. meets EN61000-3-2 (n/a 440 Hz) Downloadable GUI from website Turn-on time AC on 2.0 sec typ., inhibit/enable 150 ms typical Customer provided air option Programmable delay 50 ms internal turn-on delay (Dual Output only) uP controlled PFC input with active EMI filter CISPR 22/EN55022 Level B** inrush protection 2 I C monitor of voltage, current, and Leakage current 300 A max. 240 Vac 47 - 63 Hz temp Radiated EMI CISPR 22/EN55022 Level B** Programmable voltage, current limit, Holdover storage 20 ms minimum (independent of input Vac) additional 34 ms holdover 2 inhibit/enable through I C storage with optional HUP module (SEMI F47 compatible). Optional extended hold-up module For iMP4 15 ms (low-line), 10 ms (high-line) (SEMI F47 compliance) AC OK > 5 ms early warning min. before outputs lose regulation Increased power density to 50% over Full cycle ride thru (50 Hz) (n/a on iMP4 > 750 W 90 Vac) standard MP Harmonic distortion Meets EN61000-3-2 External switching frequency sync input Isolation Meets EN60950 and EN60601 Optional conformal coating Input to output, input to ground: 2000 Vac output to ground: 400 Vdc Industrial temp range (-40 C to 70 C) Global inhibit / enable TTL, Logic 1 and Logic 0 configurable No preload required Input fuse (internal) iMP4: 16 A iMP8: 20 A iMP1: 25 A (both lines fused) Industrial shock/vibration (> 50Gs) Warranty 2 years SAFETY UL UL60950/UL2601** CSA CSA22.2 No. 234 Level 5 UV EN60950/EN60601-1** BABT Compliance to EN60950/ EN60601 BS7002 CB Certificate and report CE Mark to LVDiMP Data Sheet Electrical Specifications Output Output (cont.) Adjustment range* 10% minimum all outputs (manual) Reverse voltage protection: 100% of rated output current 2 (full module adjustment range using I C) 2 Thermal protection* Configurable through I C Factory set point accuracy 1% (OTP and OTW) All outputs disabled when internal temp 2 exceeds safe operating range. > 5 ms I C output program 5% warning (AC OK signal) before shutdown accuracy Remote sense Up to 0.5 V total drop (not available on triple Margining 4 - 6% nominal analog (single output output module) module only) Single wire parallel Current share to within 2% of total rated Overall regulation 0.4% or 20 mV max. (1500 W modules 1% current max.) (36 W modules 4% maximum) 2 DC OK* 5% of nominal. Configurable through I C Ripple RMS: 0.1% or 10 mV, whichever is greater Pk-Pk: 1.0% or 50 mV, whichever is greater Minimum load Not required Bandwidth limited to 20 MHz Housekeeping bias voltage 5 Vdc 1.0 A max. present whenever AC Dynamic response < 2% or 100 mV, with 25% load step input is applied (Optional 2.0 A available) 2 Recovery time To within 1% in < 300 sec Module inhibit* Configured and controlled through I C 2 Overcurrent protection** Configurable through I C (calibration Switching frequency 250k Hz accepts external sync signal required). Single output module and main Output/Output isolation > 1 Megohm, 500 V output of the dual output module 105 - 120% External sync TTL clock input signal used to adjust of rated output current. Aux output of dual switching frequency. Frequency 500 kHz output module 105 - 140% of rated output 20% Duty cycle 40 - 55% current 2 Short-circuit protection: Protected for continuous short-circuit. * Can be controlled via I C 2 Recovery is automatic upon removal of short ** Controlled via I C but requires load calibration 2 Overvoltage protection* Configurable through I C Single output module: 2 - 5.5 V 122 - 134% 6 - 60 V 110 - 120% Dual output module: 2 - 6 V 122 - 134% 8 - 28 V 110 - 120% Triple output module: 110 - 120% of highest voltage rating Environmental Specifications Operating temperature -40 to 70 C ambient. Derate each output 2.5% per degree from 50 to 70 C. (-20 C start up) Storage temperature -40 C to +85 C Electromagnetic susceptibility Designed to meet EN61000-4 -2, -3, -4, -5, -6, -8, -11 Level 3 Humidity Operating non-condensing 10% to 95% RH Vibratio IEC68-2-6 to the levels of IEC721-3-2 MTBF demonstrated: > 550,000 hours at full load, 220 Vac and 25 C ambient conditions Output Module Line-up Module Code 1 2 3 5 4 Module Type Single Single Single Single Dual Triple Max output power 210 W 360 W 750 W 1500 W 144 W 36 W Max output current 35 A 60 A 150 A 140 A 10 A 2 A Output voltages available* 2 - 60 V 2 - 60 V 2 - 60 V 6 - 60 V 8 - 15*, 24 - 28 8 - 15*, 8 - 15* 8-15, 8-15, 2-6 8-15, 8-15, 8-15 8 - 15*, 2 - 6 2 - 6, 2 - 6 24 - 28, 8-15, 8-15, 18-28 8-15, 18-28, 2-6 24 - 28 24 - 28, 2 - 6 Standard voltage increments 25 25 25 18 16 18 Remote sense Yes Yes Yes Yes Yes Yes No Remote margin Yes Yes Yes Yes No No No 2 V-Program - I C Control Yes Yes Yes Yes Yes Yes No Active Current Share Yes Yes Yes Yes Yes No No 2 Module Inhibit - I C Control Yes Yes Yes Yes Yes Yes Yes Module Inhibit - Analog Yes Yes Yes Yes Yes No No Overvoltage/Overcurrent protection Yes Yes Yes Yes Yes Yes Yes Minimum load required No No No No No No No Slots occupied in any iVS case 1 2 3 4 1 1 * Note: Contact Factory for extended range down to 6 V