POWER Intelligent VS Power Data Sheet Up to 4920 Watts Total Power: Up to 4920 W TM Input Voltage: 85 - 264 Vac 380, 440 Vac 120 - 300 Vdc 1-Phase 3-Phase Color: 100% Blue, 50% Magenta, Font: Minion Bold for VS 0% Yellow, 0% Black Minion italic for i size for each is the sameV - 100% Black Created on Mac of Outputs: Up to 24 Special featureS Full medical EN60601 approval* 2 Intelligent I C control Electrical Specifications Voltage adjustment on all outputs Input 2 (manual or I C) Input ra nge iVS1 & iVS3 90 - 264 Vac 1 120 - 300 Vdc Configurable input and output OK signals and indicators iVS6 & iVS8 170 - 264 Vac 3 Configurable inhibit/enable iVS8H 396 - 480 Vac rated at 4920 W DC output 3 Configurable output UP/DOWN 342 - 480 Vac rated at 4200 W DC output 3 sequencing Frequency 47 - 440 Hz High power density (12 W/cu-in) Inrush current 40 A peak maximum (soft start) Intelligent fan (speed control/fault Efficiency Up to 85% full case load status) uP controlled PFC input with active Power Factor 0.99 typ. meets EN61000-3-2 Inrush protection Turn-on time AC on 1.5 sec typical, inhibit/enable 150ms typical Programmable 2 I C monitor of voltage, current, and 50 ms internal turn-on delay (Dual Output only) temperature EMI Filter CISPR 22/EN55022 Level B. Level A for iVS8H Programmable voltage, current limit, 2 Leakage current 500 A max. 240 Vac 47-63 Hz inhibit/enable through I C Optional extended hold-up module Radiated EMI CISPR 22/EN55022 Level B. Level A for iVS8H (SEMI F47 compliance) Holdover storage 10 ms minimum (independent of input Vac) additional 20 mSEC holdover Increased power density to 150% storage with optional HUP module (SEMI F47 compatible) Optional conformal coating AC OK > 5 ms early warning minutes before outputs lose regulation Full cycle ride thru Industrial temp range (-40 C to 70 C) (50 Hz). Programmable Uses standard iMP modules Harmonic distortion Meets EN61000-3-2 Field upgradeable firmware Isolation Meets EN60950 and EN60601 RoHS compliant Meets 1 MOPP Primary to ground, 2 MOPP Primary to Secondary* Global inhibit / enable TTL, Logic 1 and Logic 0 configurable SafetY Warranty 3 years UL UL60950/UL2601 CSA CSA22.2 No. 234 Level 5 UV EN60950/EN60601-1 BABT Compliance to EN60950/ EN60601 BS7002 CB Certificate and report CE Mark to LVD * Note: iVS8H does not have Medical or MOPP approvals.iVS Data Sheet Electrical Specifications Output 2 Adjustment range* 10% minimum all outputs (manual) (full module adjustment range using I C) Factory set point accuracy 1% 2 I C output program accuracy 5% Margining 4 - 6% nominal analog (single output module only) Overall regulation 0.4% or 20 mV max. (1500 W modules 1% max.) Ripple RMS: 0.1% or 10 mV, whichever is greater Pk-Pk: 1.0% or 50 mV, whichever is greater Bandwidth limited to 20 MHz Dynamic response < 2% or 100 mV, with 25% load step Recovery time To within 1% in < 300 sec 2 Overcurrent protection** Configurable through I C (calibration required). Single output module and main output of the dual output module 105 - 120% of rated output current. Aux output of dual output module 105 - 140% of rated output current. Special programmable OCP delay on 1500 W module from 100 mSec to 25.5 seconds with shutdown features. Short-circuit protection Protected for continuous short-circuit. Recovery is automatic upon removal of short (Shutdown mode on 1500 W module). 2 Overvoltage protection* Configurable through I C Single output module: 2 - 5.5 V 122 - 134% 6 - 60 V 110 - 120% Dual output module: 2 - 6 V 122 - 134% 8 - 28 V 110 - 120% Triple output module: 110 - 120% of highest voltage rating 2 Thermal protection* Configurable through I C All outputs disabled when internal temp exceeds safe operating range. > 5 ms warning (AC OK signal) before shutdown Remote sense Up to 0.5 V total drop (not available on triple output module) Single wire parallel Current share to within 2% of total rated current 2 DC OK* 5% of nominal. Configurable through I C Minimum load Not required Housekeeping bias voltage 5 Vdc 1.0 A max. present whenever AC input is applied Overall Regulation: 5% Ripple and Noise: 150 mV pk-pk, Bandwidth limited to 150 MHz and measured with 10 uF Tantalum capacitor and 0.1 uF ceramic capacitor in parallel on the output. 2 Module inhibit* Configured and controlled through I C Output/Output isolation > 1 Megohm, 500 V 2 * Can be controlled via I C 2 ** Controlled via I C but requires load calibration (except 1500 W module) Environmental Specifications Operating temperature -40 to 70 C ambient. Derate each output 2.5% per degree from 50 to 70 C. (-20 C start up) Storage temperature -40 C to +85 C Electromagnetic susceptibility Designed to meet EN61000-4 -2, -3, -4, -5, -6, -8, -11 Level 3 Humidity Operating non-condensing 10% to 95% RH Vibration IEC68-2-6 to the levels of IEC721-3-2 MTTF field demonstrated > 550,000 hours at full load, 220 Vac and 25 C ambient conditions