process yellow 116 1375 1797 375 3405 Embedded Power for Business-Critical Continuity 313 2985 Rev. 07.19.11 89 MP Series 1 of 8 240 MP Series 400 - 1200 Watts Total Power: 400 - 1200 Watts 242 Input Voltage: 85 - 264 VAC 120 - 350 VDC of Outputs: Up to 21 Special Features 2607 Current share on all outputs with ratings of 10 A or greater Remote sense on all outputs with ratings greater than 2 A Overload protection on all outputs 652 Voltage adjustment on all outputs Electrical Specifications Margining on all single output modules Input Input OK signal and status indicator LED Input ra nge: 85 - 264 Vac Global DC OK signal and status 120 - 350 Vdc indicator LED Frequency: 47 - 440 Hz Global and individual module inhibits/ enable Inrush current: 40 A peak max. (soft start) 2 year warranty Forced air cooling, field replaceable fan Efficiency: 70 - 80% typ. full case load Isolated 5 V bias voltage Power Factor: 0.99 typ. meets EN61000-3-2 Power factor correction EN61000-3-2 harmonic distortion Turn-on time: AC on 1.5 sec typ. compliance inhibit/enable 150 ms typ. CISPR 22, EN55022 Curve B conducted EMI filter standard: CISPR 22/EN55022 Level B / radiated EMI European CE Mark requirements EMI filter (low leakage CISPR 22/EN55022 Level A Optional VME timing and system DC option): OK module Customer-provided air option Leakage current standard: 2.0 mA max. 240 Vac Additional 200 W output high line Leakage current (low leak- 300A max. 240 Vac (180-264 VAC) age option): Low leakage option for medical applications Radiated EMI: CISPR 22/EN55022 Level B EN61000 immunity standards Standard modification flexibility Holdover storage: 20 ms minimum (independent of input Vac) (consult factory) AC OK: >5 ms early warning min. before outputs lose regulation Low noise fan Full cycle ride thru (50 Hz) Fan fail signal Module enable Harmonic distortion: Meets EN61000-3-2 Outputs down to 0.5V Isolation: Meets EN60950 F ield D emons trated MTB F: > 550,000 hours at full load, 220 Vac & 25 C Global Inhibit/Enable: TTL, Logic 1 and Logic 0 ambient conditions Input fuse (internal): MP4: 10 A MP6: 15 A MP8: 20 A MP1: 20 A Safety Warranty: 2 years UL UL1950 CSA CSA22.2 No. 234 Level 5 IEC IEC950, Class 1 VDE EN60950, BABT Compliance to EN 60950, BS 7002 CB Certificate and report CE Markprocess yellow 116 1375 1797 375 3405 313 Embedded Power for Business-Critical Continuity 2985 Rev. 07.19.11 89 MP Series 2 of 8 240 Output Output (cont.) Adjustment range: 10% minimum all outputs Thermal protection: All outputs disabled when internal temp 1 exceeds safe operating range. > 5ms Margining: 4 - 6% nominal warning (AC OK signal) before shutdown Overall regulation: 0.4% or 20mV max. 242 Remote sense: Up to 0.5 V total drop (not avbl on triple (36 W modules 4% maximum) output module) Ripple: RMS: 0.1% or 10mV, whichever is greater Single wire parallel: Current share to within 2% of total rated Pk-Pk: 1.0% or 50mV, whichever is greater 2 current Bandwidth limited to 20 MHz DC OK: -2% to -8% of nominal for any monitored Dynamic response: < 2% or 100 mV, with 25% load step 2607 2 output Recovery time: To within 1% in < 300 sec Minimum load: Not required on single or triple output. 10% Overcurrent Single output module & main output of 3 required on main of dual output dual output module protection:** Housekeeping bias 5 Vdc 1.0 A max. present whenever AC 105-120% of rated output current. 652 voltage: input is applied Aux output of dual output module 105- Module inhibit: TTL, isolated, singles and dual (both 140% of rated output current outputs) only Short-circuit protection: Protected for continuous short-circuit Switching frequency: 250k Hz Recovery auto upon removal of short Output/Output isolation: >1 Megohm Overvoltage protection: VME signal option board: POR signal & quad external DC OK (measured at sense Hold-up module (HUP): 1-slot module providing additional 34mSec connection) (60mSec total) hold-up 600 W loading. Single output module: 2-5.5 V 122-134% 6-60 V 100-120% Dual output module: 2-6 V 122-134% 8-28 V 110-120% 1. Single output modules only. Triple output module: No overvoltage protection provided. 2. Single and main of dual output modules only Recycle AC input voltage to reset OVP 3. Contact factory for optional preload if required circuit Reverse voltage protection: 100% of rated output current Field Demonstrated MTBF: > 550,000 hours at full load, 220 Vac and 25 C ambient conditions Environmental Specifications Operating temperature: -20 C to 50 C (start 0 C) (derate each output linearly to 50% at 70 C) (-20 C to 40 C max. with rear air option) Shock/Vibration: Mil-Hdbk 810E Humidity: 95% non-condensing Storage temperature: -40 C to 85 C Temperature coefficient: 0.02% per C Cooling: Internal DC fan or customer provided air (option) Output Module Line-up Module Type Single Single Single Dual Triple 3 Output 1 1 2 36 W Max output power 210 W 360 W 600 W 144 W 2 A Max output current 35 A 60 A 120 A 10 A Volts 2-60 V 2-60 V 2-60 V 2-28 V 2-28V Standard voltage increments 25 25 25 19 18 No Remote sense on outputs Yes Yes Yes Yes, both No Remote margin/V-Program Yes Yes Yes No -- Module Inhibit (isolated) Yes Yes Yes -- Single wire active current share Yes Yes Yes Yes, main only -- Over voltage / over current protection Yes Yes Yes Yes Over current Minimum load required No No No Yes (10%) main only No 1 Slots occupied in any MP case 1 2 3 1