POWER SIL/SMT20C2 Series Data Sheet C-Class Non-Isolated Total Power: 20 Amps Input Voltage: 4.5 - 13.8 Vdc of Outputs: Single SPECIAL FEATURES 20 A current rating Input voltage range: 4.5 - 13.8 Vdc Output voltage: 0.59 - 5.1 V Industry-leading value Electrical Specifications Cost optimized design Input Excellent transient response Input voltage ra nge 4.5 - 13.8 Vdc Output enable Input current Minimum load 50 mA Output voltage adjustability Remote OFF 5 mA Path for future upgrades Input current (max.) See Note 3 18 A lo max. Supports silicon voltage migration Start-up time Remote ON/OFF 3 ms Reduced design-in and qual time Output Current sink capability Output voltage See Note 5 0.59 - 5.1 V RoHS compliant Output setpoint accuracy 0.1% trim resistors 1.0% Two year warranty Line regulation Low line to high line 0.2% Load regulation Full load to min. load 0.5% SAFETY Min./max. load 0 A/20 A UL, cUL CAN/CSA 22.2 No. Overshoot At turn-on 0.5% max. TV Product Service (EN60950) Undershoot At turn-off 100 mV max. CB report and certificate to Ripple and noise See Note 1 30 mV IEC60950 5 Hz to 20 MHz Vin = 5 V, Vout = 2.5 V Transient response See Note 1, 2 130 mV max. deviation 50 s recovery to within regulation band General Efficiency Vin = 5 V, Vo = 2.5 V, lo = 20 A 90% Switching frequency Fixed 750 kHz Material flammability UL94V-0 Approvals and standards EN60950 UL/cUL6950 Weight 8.50 g (0.03 oz.) MTBF 12 V 40 C, 100% load 6,721,853 hours Bellcore 332 Coplanarity 150 m All specifications are typical at nominal input, full load at 25 C, unless otherwise stated.SIL/SMT20C2 Series Data Sheet Environmental Specifications Thermal performance Operating ambient temperature -0 C to +70 C See Note 5 Non-operating temperature -40 C to +125 C Protection Short-circuit Hiccup, non-latching Overvoltage protection Hiccup, non-latching Recommended System Capacitance Input See Note 6 0 F Output See Note 7 0 F Ordering Information Regulation Model Output Power Input Output Output Current Output Current Efficiency (8) Number (Max.) Voltage Mount Voltage (Min.) (Max.) (Typical) Line Load SIL20C2-00SADJ-HJ 100 W 4.5 - 13.8 Vdc Horizontal 0.59 - 5.1 V 0 A 20 A 93% 0.2% 0.5% SIL20C2-00SADJ-VJ 100 W 4.5 - 13.8 Vdc Vertical 0.59 - 5.1 V 0 A 20 A 93% 0.2% 0.5% SMT20C2-00SADJJ 100 W 4.5 - 13.8 Vdc Horizontal 0.59 - 5.1 V 0 A 20 A 93% 0.2% 0.5% Surface Mount Part Number System with Options Product Family Rated Output Performance Generation Input Voltage Output Voltage Mounting Option RoHS Compliance Current SXX 20 C 2 - 00 SADJ - V J SIL = Single In Line 06 = 6 Amp C = Cost Blank = Standard 00 = 4.5 - 13.8 V Single Adjustable V = Vertical J = Pb free (RoHS SMT = Surface Mount 15 = 15 Amp Optimized 2 = Increased Output H = Horizontal 6/6 compliant) 20 = 20 Amp current density Blank = Horizontal 30 = 30 Amp Surface Mount 40 = 40 Amp Output Voltage Adjustment Standard Application Drawing The ultra-wide output voltage trim range offers major advantages to users Power Good who select the SIL/SMT40C2 series. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be trimmed in a range of 0.59 - 5.1 V. When the SIL20C2 converter leaves the factory, the output has been adjusted to the default voltage of 0.59 V. 4 V 1 out Enable 5 Notes: 7 +R sense 1. Measured as per recommended system capacitance. SIL20C2 2. di/dt = 10 A/s, Vin = Nom, Tc = 25 C, load change = 0.75 lo to full lo and full lo to 0.75. R 3. External input fusing is recommended. C out V in L 6 8 4. Additional part numbers may be available with different output voltages. 3 2 O A 5. Airflow dependent, 100 LFM minimum required. D C in 6. No capacitors needed for ripple current stability. R trim 7. No capacitors needed for stability. (for trim -R sense 8. NOTICE: Some models do not support all options. Please contact your local Artesyn Embedded down) Technologies representative or use the on-line model number search tool at GND