Blackhawk 4 CCStudio Setup QUICK PCI560 A.) Importing a Pre-defined Import or Factory Board START These instructions apply to CCStudio v2.2 - v3.3, but the import dialog varies slightly be- JTAG tween versions. Refer to the PCI560 Installation Guide if more information is needed. GUIDE 1. Run CCStudio Setup. And for CCStudio v3.0 and earlier, start the Import a Emulator (PCI560 ) Configuration dialog. 2. Find and select bh-pci560 emulator from the Platform pull down menu Installation Requirements located at the top of the middle CCSetup window or in the center of the import Personal computer with at least one free PCI Slot. dialog box (this will list the PCI560 imports). Windows 2000/XP/Vista Operating Systems (32 or 64-bit versions). 3. You can narrow down the import options further by using the Family pull down Texas Instruments Code Composer Studio version 2.2 or later. (i.e. select C55xx to list all TMS320C55x device imports). CD ROM Drive. 4. When you find your target, or an import close to it, highlight the entry and choose the option to add it to your system. Inventory of Items Included 5. If this import setup does not completely match your target, you can edit the prop- IMPORTANT erties manually (i.e. to add or change a GEL file). 1. Blackhawk PCI560 PC Board. ENVIRONMENTAL 2. XDS560 Rev D JTAG cable. 6. When finished, save the setup and start CCStudio. CONSIDERATIONS 3. 20e cTI-14t TI Pin Converter This equipment is designed to 4. 20e cTI-20t ARM Pin Converter be operated under the follow- B.) Using Create Board for CCStudio v3.1 and later 5. 20e cTI-60t TI Pin Converter ing environmental conditions: 6. Installation CD ROM. 1. Run CCStudio Setup. Temperature between 0C 7. Warranty and Product Registration 2. Select the Create Board tab and drag the BH PCI560 Connection to 55C. Relative Humidity of Card. My System on the left. This will prompt you for a connection name. You can 20% - 70% non-condensing. 8. Quick Start Guide. enter any string you want, but at a minimum, it typically includes the emulator Operation of the unit outside of 9. Low-Profile PCI Bracket name and target DSP or board name (i.e. Blackhawk PCI560C5509). the above range may affect 3. Now, highlight the new connection name you added under My System and add structual and mechanical the available processor(s) from the middle window to match your hardware. integrity and cause permanent Other Items Required damage. 4. Save your setup and start CCS. 1. Target Board Systema self- Caution is necessasry to powered board with a TI DSP and minimize ESD (Electro-stactic compatible JTAG header connec- C.) Changing an XDS560 PCI import for CCStudio v2.2-v3.0 Discharge) which can damage tion conforming to IEEE 1149.1 electronic components. Use in 1. Run CCStudio Setup and import a setup for the TI XDS560 PCI card that Standard. a controlled environment matches your target (refer to section (A.) above for importing). 2. Copy of Code Composer where ESD materials and 2. Highlight the board you added under My System, right click with the mouse and practices are employed is Studio Version 2.2 or later. choose properties. highly recommended. 3. Locate the Emulator Name field under board properties tab and change the name from XDS560 0 to BH560PCI 0. If you need to change other proper- ties (GEL, DSP, etc.) , you can do that too. 1 2 3 4 5 6 7 8 9 4. Save CCSetup and start CCS. For CCStudio v2.0 and v2.1 (only), download the XDS560 emulation driver subsystem from the TI web site: 1 Emulation Driver Installation PCI PnP Installation 3 The PCI560 JTAG Emulator shipped with its emulation drivers on CD ROM Windows 2000/XP/Vista media that are needed by Windows and CCStudio for operation. 1. Make sure the PCI560 Emulator is installed. 2. Boot the computer and log in. 1. Insert the Emulation Driver CDROM into your PCs CDROM drive. 3. Follow the Windows Found New Hardware wizard prompts. 2. Follow the installation wizard, and when done, you are ready to install the emulator hardware. 4. You can select the automatic option for locating drivers. If the installation executable fails to start automatically, run X: Setup Setup.exe, where X is the drive letter for your CD ROM drive. 5. If the automatic option did not locate them, you can manually specify the location. These files were installed to your system during the Emulation Driver Installation - section 1. The typical location for these files is 2 Hardware Installation folder: C: CCStudio v3.3 blackhawk drivers.1 , where <C: CCStudio v3.3> is the location selected in section 1. WARNING Be careful to connect interface cables with the correct orientation. Pin 1 on the 6. When completed, the Blackhawk Control Panel and Windows Device interface cable should match Pin 1 on the DSP system connector. The JTAG Manager will show the device. The Blackhawk Control Panel can be cable assembly features akeye connector to minimize the chance of error. activated from its icon, located in the Windows Control Panel Dialog Box. Do not force cables into position. Forcing them may damage the cables or the interconnected boards and systems. 7. Now follow the Code Composer Studio Setup in section 4. 1. Power down your computer and open the case to gain access to an available PCI slot. 2. Install the PCI560 board (see Figure 2) making sure to secure the PCI Standard end plate to the case. If your PC requires a low profile bracket, one has PCI been included to easily replace the standard (taller) bracket. Please refer Bracket to the section in the Installation Guide for detailed instructions for replac- ing the bracket. 3. Attach the JTAG cable assembly to the corresponding D connector of the PCI560 (see Figure 1). 4. Close the computer case and boot the machine. 5. Follow the Plug-N-Play Found New Hardware Wizard to install device drivers (see section 3 on PCI PnP Installation). Low-profile PCI Bracket D connector FIGURE 1 - PCI560 with XDS560 JTAG Cable and Pod Assembly FIGURE 2 - PCI560 Installation 3 2