ACPL-330J 1.5 Amp Output Current IGBT Gate Driver Optocoupler with Integrated (V ) Desaturation Detection, UVLO, CE Fault Feedback, Active Miller Clamp and Auto-Fault Reset Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available -xxxE denotes a lead-free product Description Features The ACPL-330J is an advanced 1.5 A output current, easy- 1.5 A maximum peak output current to-use, intelligent gate driver which makes IGBT VCE fault 1.0 A minimum peak output current protection compact, affordable, and easy-to implement. 250 ns maximum propagation delay over Features such as integrated V detection, under CE temperature range voltage lockout (UVLO), soft IGBT turn-off, isolated open collector fault feedback and active Miller clamping 1.0A Active Miller Clamp. Clamp pin short to V if not EE provide maximum design flexibility and circuit protec - in used tion. Miller Clamping The ACPL-330J contains a AlGaAs LED. The LED is Desaturation Detection optically coupled to an integrated circuit with a power Under Voltage Lock-Out Protection (UVLO) output stage. ACPL-330J is ideally suited for driving with Hysteresis power IGBTs and MOSFETs used in motor control inverter Open Collector Isolated fault feedback applications. The voltage and current supplied by these optocouplers make them ideally suited for directly Soft IGBT Turn-off driving IGBTs with ratings up to 1200 V and 100 A. For Automatic Fault Reset after fixed Mute Time , typically IGBTs with higher ratings, the ACPL-330J can be used to 26ms drive a discrete power stage which drives the IGBT gate. Available in SO-16 package The ACPL-330J has an insulation voltage of V = 1414 IORM V . PEAK 100 ns maximum pulse width distortion (PWD) 50 kV/s minimum common mode rejection (CMR) Block Diagram at V = 1500 V CM 13 V CC2 I < 5 mA maximum supply current CC(max) UVLO Wide V operating range: 15 V to 30 V over 6, 7 D CC ANODE R temperature range 11 I 5, 8 V OUT V CATHODE DESAT Wide operating temperature range: 40C to 105C LED1 E 14 R DESAT Safety Approvals: 9, 12 UL, 5000 V for 1 minute, CSA Approval, RMS V EE SHIELD IEC/EN/DIN-EN 60747-5-5 V = 1414 V IORM PEAK V CLAMP 2 10 Applications V CC1 V CLAMP LED2 3 V Isolated IGBT/Power MOSFET gate drive E FAULT 16 AC and brushless DC motor drives Industrial inverters and Uninterruptible Power Supply 1, 4 15 V S V LED SHIELD (UPS) CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. The components featured in this datasheet are not to be used in military or aerospace applications or environments.Pin Description Pin Symbol Description 1 V Input Ground S 11 VV VV 1616 2 V Positive input supply voltage. (3.3 V to 5.5 V) CC1 SS EE 3 FAULT Fault output. FAULT changes from a high impedance state 22 VV to a logic low output within 5 s of the voltage on the VV 1515 CC1CC1 LELEDD DESAT pin exceeding an internal reference voltage of 6.5 V. FAULT output is an open collector which allows the FAULT 33 FAFAULULTT DEDESASATT 1414 outputs from all ACPL-330J in a circuit to be connected together in a wired OR forming a single fault bus for inter- 44 VV VV 1313 SS facing directly to the micro-controller. CC2CC2 4 V Input Ground S 55 CACATHTHODODEE VV 1212 EEEE 5 CATHODE Cathode 6 ANODE Anode 66 ANOANODEDE VV 1111 OUOUTT 7 ANODE Anode 8 CATHODE Cathode 77 ANOANODEDE VV 1010 CLCLAMAMPP 9 V Output supply voltage. EE 88 CACATHTHODODEE VV 99 10 V Miller clamp EEEE CLAMP 11 V Gate drive voltage output OUT 12 V Output supply voltage. EE 13 V Positive output supply voltage CC2 14 DESAT Desaturation voltage input. When the voltage on DESAT exceeds an internal reference voltage of 6.5 V while the IGBT is on, FAULT output is changed from a high impedance state to a logic low state within 5 s. 15 V LED anode. This pin must be left unconnected for guaran- LED teed data sheet performance. (For optical coupling testing only) 16 V Common (IGBT emitter) output supply voltage. E Ordering Information ACPL-330J is UL Recognized with 5000 Vrms for 1 minute per UL1577. Option Surface IEC/EN/DIN EN Part number RoHS Compliant Package Mount Tape& Reel 60747-5-5 Quantity ACPL-330J -000E SO-16 X X 45 per tube -500E X X X 850 per reel To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: ACPL-330J-500E to order product of SO-16 Surface Mount package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-5 Safety Approval in RoHS compliant. Example 2: ACPL-330J-000E to order product of SO-16 Surface Mount package in tube packaging with IEC/EN/DIN EN 60747-5-5 Safety Approval and RoHS compliant. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information. Remarks: The notation XXX is used for existing products, while (new) products launched since 15th July 2001 and RoHS compliant option will use -XXXE. 2