ACPL-332J 2.5 Amp Output Current IGBT Gate Driver Optocoupler with Integrated (V ) Desaturation Detection, UVLO CE Fault Status Feedback and Active Miller Clamping Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available -xxxE denotes a lead-free product Description Features The ACPL-332J is an advanced 2.5 A output current, easy- Under Voltage Lock-Out Protection (UVLO) with to-use, intelligent gate driver which makes IGBT V fault Hysteresis CE protection compact, affordable, and easy-to implement. Desaturation Detection Features such as integrated V detection, under CE Miller Clamping voltage lockout (UVLO), soft IGBT turn-off, isolated open collector fault feedback and active Miller clamping Open Collector Isolated fault feedback provide maximum design flexibility and circuit protec - Soft IGBT Turn-off tion. Fault Reset by next LED turn-on (low to high) after The ACPL-332J contains a AlGaAs LED. The LED is fault mute period optically coupled to an integrated circuit with a power Available in SO-16 package output stage. ACPL-332J is ideally suited for driving Safety approvals: UL approved, 5000 V for 1 power IGBTs and MOSFETs used in motor control inverter RMS minute, CSA approved, IEC/EN/DIN-EN 60747-5-5 applications. The voltage and current supplied by these approved V = 1414 V optocouplers make them ideally suited for directly IORM PEAK driving IGBTs with ratings up to 1200 V and 150 A. For Specifications IGBTs with higher ratings, the ACPL-332J can be used to drive a discrete power stage which drives the IGBT gate. 2.5 A maximum peak output current The ACPL-332J has an insulation voltage of V = 1414 IORM 2.0 A minimum peak output current V . PEAK 250 ns maximum propagation delay over temperature range Block Diagram 100 ns maximum pulse width distortion (PWD) 13 V CC2 50 kV/s minimum common mode rejection (CMR) at UVLO 6, 7 V = 1500 V D CM ANODE R 11 I I < 5 mA maximum supply current CC(max) 5, 8 V OUT V CATHODE DESAT LED1 E Wide V operating range: 15 V to 30 V over 14 CC R DESAT temperature range 9, 12 V EE 1.7 A Miller Clamp. Clamp pin short to V if not used EE SHIELD V Wide operating temperature range: 40C to 105C CLAMP 2 10 V CC1 V CLAMP Applications LED2 3 V E FAULT 16 Isolated IGBT/Power MOSFET gate drive AC and brushless DC motor drives 1, 4 15 V Industrial inverters and Uninterruptible Power Supply S V LED SHIELD (UPS) CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. The components featured in this datasheet are not to be used in military or aerospace applications or environments.Pin Description Pin Symbol Description 1 V Input Ground S 11 VV VV 1616 SS 2 V Positive input supply voltage. (3.3 V to 5.5 V) EE CC1 3 FAULT Fault output. FAULT changes from a high impedance state 22 VV VV 1515 CC1CC1 to a logic low output within 5 s of the voltage on the LELEDD DESAT pin exceeding an internal reference voltage of 7 V. FAULT output is an open collector which allows the FAULT 33 FAFAULULTT DEDESASATT 1414 outputs from all ACPL-332J in a circuit to be connected together in a wired OR forming a single fault bus for inter- 44 VV VV 1313 SS CC2CC2 facing directly to the micro-controller. 4 V Input Ground S 55 CACATHTHODODEE VV 1212 EEEE 5 CATHODE Cathode 6 ANODE Anode 66 ANOANODEDE VV 1111 OUOUTT 7 ANODE Anode 8 CATHODE Cathode 77 ANOANODEDE VV 1010 CLCLAMAMPP 9 V Output supply voltage. EE 88 CACATHTHODODEE VV 99 10 V Miller clamp EEEE CLAMP 11 V Gate drive voltage output OUT 12 V Output supply voltage. EE 13 V Positive output supply voltage CC2 14 DESAT Desaturation voltage input. When the voltage on DESAT exceeds an internal reference voltage of 6.5 V while the IGBT is on, FAULT output is changed from a high impedance state to a logic low state within 5 s. 15 V LED anode. This pin must be left unconnected for guaran- LED teed data sheet performance. (For optical coupling testing only) 16 V Common (IGBT emitter) output supply voltage. E Ordering Information ACPL-332J is UL Recognized with 5000 Vrms for 1 minute per UL1577. Option Surface IEC/EN/DIN EN Part number RoHS Compliant Package Mount Tape& Reel 60747-5-5 Quantity ACPL-332J -000E SO-16 X X 45 per tube -500E 850 per reel X X X To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: ACPL-332J-500E to order product of SO-16 Surface Mount package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-5 Safety Approval in RoHS compliant. Example 2: ACPL-332J-000E to order product of SO-16 Surface Mount package in tube packaging with IEC/EN/DIN EN 60747-5-5 Safety Approval and RoHS compliant. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information. Remarks: The notation XXX is used for existing products, while (new) products launched since 15th July 2001 and RoHS compliant option will use -XXXE. 2