ACPL-333J 2.5 Amp Output Current IGBT Gate Driver Optocoupler with Integrated (V ) Desaturation Detection, UVLO CE Fault Status Feedback, Active Miller Clamp and Auto-Fault Reset Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available -xxxE denotes a lead-free product Description Features The ACPL-333J is an advanced 2.5 A output current, easy- 2.5 A maximum peak output current to-use, intelligent gate drivers which make IGBT V fault CE 2.0 A minimum peak output current protection compact, affordable, and easy-to implement. 250 ns maximum propagation delay over temperature Features such as integrated V detection, under voltage CE range lockout (UVLO), soft IGBT turn-off, isolated open collector fault feedback, active Miller clamping and Auto- 1.7A Active Miller Clamp.Clamp pin short to V if not EE fault reset provide maximum design flexibility and circuit used protection. Desaturation Detection The ACPL-333J contains a AlGaAs LED. The LED is optically Under Voltage Lock-Out Protection (UVLO) with coupled to an integrated circuit with a power output Hysteresis stage. ACPL-333J are ideally suited for driving power IGBTs Open Collector Isolated fault feedback and MOSFETs used in motor control inverter applications. Soft IGBT Turn-off The voltage and current supplied by these optocouplers make them ideally suited for directly driving IGBTs with Automatic Fault Reset after fixed mute time , typical ratings up to 1200 V and 150 A. For IGBTs with higher 26ms ratings, the ACPL-333J can be used to drive a discrete Available in SO-16 package power stage which drives the IGBT gate. The ACPL-333J 100 ns maximum pulse width distortion (PWD) have an insulation voltage of V = 1414 V . IORM PEAK 50 kV/s minimum common mode rejection (CMR) at Block Diagram V = 1500 V CM 13 I < 5 mA maximum supply current CC(max) V CC2 UVLO Wide V operating range: 15 V to 30 V over CC 6, 7 D temperature range ANODE R 11 I 5, 8 V OUT Wide operating temperature range: 40C to 105C V CATHODE DESAT LED1 E 14 Safety approvals: R DESAT UL approval, 5000 V for 1 minute, CSA approval, RMS 9, 12 V EE IEC/EN/DIN-EN 60747-5-5 approval V = 1414 V IORM PEAK SHIELD V CLAMP Applications 2 10 V CC1 V CLAMP Isolated IGBT/Power MOSFET gate drive LED2 3 V E FAULT 16 AC and brushless DC motor drives Industrial inverters and Uninterruptible Power Supply 1, 4 (UPS) 15 V S V LED SHIELD CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. The components featured in this datasheet are not to be used in military or aerospace applications or environments.Pin Description Pin Symbol Description 1 V Input Ground S 1 V 2 V Positive input supply voltage. (3.3 V to 5.5 V) V 16 CC1 S E 3 FAULT Fault output. FAULT changes from a high impedance state 2 V to a logic low output within 5 s of the voltage on the V 15 CC1 LED DESAT pin exceeding an internal reference voltage of 6.5 V. FAULT output is an open collector which allows the FAULT 3 FAULT DESAT 14 outputs from all ACPL-333J in a circuit to be connected together in a wired OR forming a single fault bus for inter- 4 V V 13 S CC2 facing directly to the micro-controller. 4 V Input Ground S 5 CATHODE V 12 EE 5 CATHODE Cathode 6 ANODE Anode 6 ANODE V 11 OUT 7 ANODE Anode 7 ANODE V 10 CLAMP 8 CATHODE Cathode 9 V Output supply voltage. EE 8 CATHODE V 9 EE 10 V Miller clamp CLAMP 11 V Gate drive voltage output OUT 12 V Output supply voltage. EE 13 V Positive output supply voltage CC2 14 DESAT Desaturation voltage input. When the voltage on DESAT exceeds an internal reference voltage of 6.5 V while the IGBT is on, FAULT output is changed from a high impedance state to a logic low state within 5 s. 15 V LED anode. This pin must be left unconnected for guaran- LED teed data sheet performance. (For optical coupling testing only) 16 V Common (IGBT emitter) output supply voltage. E Ordering Information ACPL-333J is UL Recognized with 5000 Vrms for 1 minute per UL1577. Option Surface IEC/EN/DIN EN Part number RoHS Compliant Package Mount Tape& Reel 60747-5-5 Quantity ACPL-333J -000E SO-16 45 per tube X X -500E X X X 850 per reel To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: ACPL-333J-500E to order product of SO-16 Surface Mount package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-5 Safety Approval in RoHS compliant. Example 2: ACPL-333J-000E to order product of SO-16 Surface Mount package in tube packaging with IEC/EN/DIN EN 60747-5-5 Safety Approval and RoHS compliant. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information. Remarks: The notation XXX is used for existing products, while (new) products launched since 15th July 2001 and RoHS compliant option will use -XXXE. 2